User manual SEGA SPORTS JAM UNIVERSAL KIT

[. . . ] SW1 8-Ways SW2 PLAYER 1 1 PLAYER 2 INSTALLATION INSTRUCTIONS 1) First. Locate the original game Logic PCB's & Power Supply and remove from the Cabinet by first disconnecting all harnesses from the boards. (You need only to splice in the Main Power (110v AC) into the 3-Pin Connector (GRN/WHT/BLK). ) 2) Remove all existing game harnesses (we suggest using New Jamma Harnesses (NOT contained in the kit) to ensure reliability). 3) Locate the most convenient and open area of the cabinet to mount the Sports Jam GD-Rom System Asm. [. . . ] However, where special attention is required this is indicated by a thick line, the word "IMPORTANT" and its sign in this manual. STOP Indicates that mishandling the product by disregarding this display can cause the product's intrinsic performance not to be obtained, resulting in malfunctioning. IMPORTANT STOP IMPORTANT When using the cabinet that shares the coin chute between 1P and 2P (such as the NAOMI CABINET, BLAST CITY, etc. ), change the setting of the COIN CHUTE TYPE item in the COIN ASSIGNMENTS screen, from INDIVIDUAL to COMMON. Using these cabinets with the setting of INDIVIDUAL disables to play from the 2P side. For more information about the COIN ASSIGNMENTS screen, see the Naomi Service Manual. When having connected the power for the first time, open the SYSTEM MENU - GAME TEST MODE - INPUT TEST screen and test the input devices; thereby make sure that they can function normally. This game cannot support the competitor connection kit of the NAOMI CABINET. When connecting the wire to the control panel, therefore, connect it only to a single I/O board. 9 1. HANDLING PRECAUTIONS To prevent electric shock or IC Board malfunctioning, be sure to turn off the power for the cabinet when installing or removing the IC Board. Extraneous matter such as dust on the IC Board can cause the IC Board to generate heat and result in a fire due to short circuit, etc. Using NAOMI for the cabinet other than those compatible with JVS can cause generation of heat and a fire. STOP Be sure to connect the IC Board and connectors completely. For the IC Board circuit inspection, only the use of Logic Tester is permitted. The use of ordinary testers is not permitted as these can damage the IC Board. Do not subject the IC Board to static electricity when installing the IC Board in the cabinet or when connecting wire harness connectors to the IC Board. to the wire harnesses, be sure to remove the wire harnesses from the IC Board so as not to subject the IC Board to heat. NAOMI can not be used for the cabinet incorporating a monitor or projector not corresponding to 15kHz or 31kHz. Concerning the display of JAMMA VIDEO STANDARD: JAMMA VIDEO STANDARD adopted by NAOMI is referred to as JVS. As against this Standard, the conventional JAMMA STANDARD which employs 56P Edge Connectors adopted by ST-V, etc. The specific Manual attached to each game sometimes displays JVS as JV STANDARD, New JAMMA STANDARD, or JAMMA 2 STANDARD AGAINST OLD JAMMA STANDARD as JAMMA STANDARD, JS, etc. The contents herein described are subject to change without notice. IMPORTANT 10 2. SPECIFICATIONS 1 ON-SCREEN DISPLAY Monitor Position HORIZONTAL 2 CONTROL PANEL Synchronous Frequency 15/31 kHz 8WAYS SW2 1P SW1 START SW 2P 8WAYS SW2 SW1 PLAYER 1 PLAYER 2 3 Minimum DIMM Memory Capacity 256 MB 11 3. HOW TO PLAY THE GAME Introduction to the Game A player plays the most popular sports in the world (8 events and 12 games). The player aims to take first money and thereby to be designated as a KING OF SPORTS. Stages toward a KING OF SPORTS Following the 3 stages, a player ventures to play the events, one each on a stage. SYSTEM MENU When settings are changed in SYSTEM ASSIGNMENTS, COIN ASSIGNMENTS, and GAME ASSIGNMENTS of GAME TEST MODE, be sure to exit from the test mode of SYSTEM MENU screen. The contents of setting changes are stored in the IC on the BOARD when exiting from the Test Mode. [. . . ] When cleaning the disks, do not use volatile chemicals (benzine, thinner, etc. ), cleaning sprays, and antistatic agents. Do not attach papers or seals onto the disks; do not scratch the disks. Observing these instructions, do not insert such a non-usable disk into the GD-ROM drive. When cleaning a heavily contaminated disk, use clean cloth that has been soaked in water and squeezed. [. . . ]