User manual SEGA POKEMON CATCH

[. . . ] 09/01/00) 901 Cambridge Drive Elk Grove Village, IL 60007-2434 Phone: (847) 364-9787 FAX: (847) 364-9831 Internet: www. sammyusa. com DIP SWITCH SETTING (Pokemon' Catch) DIPSW 1 FUNCTIONS SETTING SW1 SW2 SW3 DIP SW SW4 SW5 SW6 SW7 SW8 BULK SETTING OFF ON OFF ON OFF ON OFF ON ATTRACT SOUND ON OFF 30 SECONDS PLAY TIME PER 1 CREDIT 35 SECONDS 40 SECONDS 45 SECONDS 50 SECONDS 55 SECONDS 60 SECONDS 75 SECONDS FREE PLAY OFF ON OFF ON OFF ON OFF ON OFF ON OFF OFF ON ON OFF OFF ON ON OFF OFF OFF OFF ON ON ON ON OFF ON ON OFF DIPSW 2 FUNCTIONS SETTING 1 COIN / 1 CREDIT 2 COINS / 1 CREDIT DIP SW NOTE $0. 25 per play $0. 50 per Play $0. 75 per play $1. 00 per play $1. 25 per play $1. 50 per play $1. 75 per play $2. 00 per play $2. 50 per play $3. 00 per play $3. 50 per play $4. 00 per play $4. 50 per play $5. 00 per play Dollar Coin per 2 play Dollar Coin per 4 play SW1 SW2 SW3 SW4 OFF OFF OFF OFF ON OFF OFF OFF OFF ON OFF OFF OFF ON OFF ON OFF ON ON OFF ON ON ON ON COIN CHUTE 3 COINS / 1 CREDIT 4 COINS / 1 CREDIT 5 COINS / 1 CREDIT 6 COINS / 1 CREDIT 7 COINS / 1 CREDIT 8 COINS / 1 CREDIT 10 COINS / 1 CREDIT 12 COINS / 1 CREDIT 14 COINS / 1 CREDIT 16 COINS / 1 CREDIT 18 COINS / 1 CREDIT 20 COINS / 1 CREDIT 1 COIN / 2 CREDITS 1 COIN / 4 CREDITS OFF OFF ON OFF OFF OFF ON ON ON ON ON ON OFF OFF OFF ON OFF ON OFF OFF ON ON ON OFF OFF ON ON ON ON OFF ON ON ON ON ON OFF OFF OFF OFF ON TEST MODE HOW TO GO TO TEST MODE ?Open Upper Coin Door and presss TEST Switch on COUNTERS & SWITCHES BRACKET to machine will go to TEST mode. Press SERVICE Switch at normal game mode to give the free credit without coin in counter up. [. . . ] SCORE LED will display the number when the Ball is caught by Character panel. Press SERVICE switch again to stop above test. Ball passing sensor, lifter Wheel Sensor B SENSOR TEST 1 2 3 Press TEST switch to display "3" on Wheel TIME LED Display to select this Sensor A mode. Re-press to switch stop. SCORE Limit Switch (R) Character Motor, Spinning Sensor Ball Switch 1 (R) Ball Switch 2 (L) Ball passing sensor COIN LOCK OUT COIL TEST (Option) * * Use this test only the customer who uses Lock out Coil to the Coin selector optionally. Press TEST switch to display "4" on TIME LED Display to select this mode. Credit is not counted in CPU memory. MOTOR UNIT TEST 1 2 Press TEST switch to display "5" on TIME LED Display to select this mode. 2 of DOTS of SCORE LED block light up when the Ball Switch 1 and 2 are ON. (Refer above picture. ) also, SCORE LED will count the balls. HOPPER TEST 1 2 3 4 Press TEST switch to display "6" on TIME LED Display to select this mode. Press SERVICE switch to payout the Capsule and Prize out counter will count once. (Sensed by Capsule. ) SCORE LED Block, "Left digit, position E" will light up when the Hopper Turning Switch is ON. SOUND TEST 1 2 3 Press TEST switch to display "7" on TIME LED Display to select this mode. Press SERVICE switch to output the all of Voice and Effect sound one by one. (loop) After one turn, Prize payout lamp will light up. DIPSW CONFIRMING TEST 1 2 Press TEST switch to display "8" on TIME LED Display to select this mode. Right digit of SCORE LED blocks will light up when the each of DIP switch are ON position. Refer below. Right digit of SCORE LED Display DIP SWITCH ON MAIN PCB 1 6 2 7 ON 5 4 3 1 8 2 3 4 5 6 7 8 BULK HOPPER (Option Unit) TEST 1 2 3 2 Press TEST switch to display "9" on TIME LED Display to select this mode. (No payout counter for Bulk Capsule) If any problem, machine will out put the Alarm sound. (Sensed by Capsule. ) SCORE LED Block, "Left digit, position E" will light up when the Bulk Payout Sensor is ON. NOTE: COIN COUNT TEST 1 2 During TEST mode except MODE 4, coin count switch and Coin In Counter are active. then check the Coin In Counter works. ERROR CODE CAPSULE EMPTY TIME LED will display "C" and output Alarm sound. [. . . ] Need exchange those. E0 E1 E2 E3 E4 Malfunction of Payout switch on Hopper unit. Malfunction of Ball passing switch Coin Switch Error E5 E6 Malfunction of Spinning sensor on Character Motor. Malfunction of Ball Rail Sensor TIME LED # Contents of ERROR Problem of Lifter Ball Sensor . Cause of problem and Solution. Check the Payout sensor of Bulk Hopper. E7 E8 E9 C0 C1 EA Lifter Motor Problem. Doll Limit Switch problem. Main Hopper empty Bulk Hopper (Option Unit) empty Bulk Hopper Payout Sensor error. [. . . ]