User manual SEGA PLANET HARRIER TWIN TYPE

[. . . ] 4201-6604-01 Warranty Your new Sega Product is covered for a period of 90 days from the date of shipment. This certifies that the Printed Circuit Boards, Power Supplies and Monitor are to be free of defects in workmanship or materials under normal operating conditions. This also certifies that all Interactive Control Assemblies are to be free from defects in workmanship and materials under normal operating conditions. Sellers sole liability in the event a warranted part described above fails shall be, at its option, to replace or repair the defective part during the warranty period. [. . . ] Entering the TEST mode clears fractional number of coins less than one credit and BONUS ADDER data. 32 TABLE 9 EXPLANATION OF TEST MODE ITEMS INSTALLATION OF MACHINE DESCRIPTION When the machine is installed, perform the following: 1. Check to see that each setting is as per standard setting made at the time of shipment. In the INPUT TEST mode, check such input devices as each SW, V. R. , etc. In the OUTPUT TEST mode, check such output devices as lamps, motors, etc. Choose MEMORY TEST in the MENU mode to allow the MEMORY test to be performed. In this test, PROGRAM RAMs, ROMs, and ICs on the IC Board are checked. In the OUTPUT TEST mode, check such output devices as lamps, motors, etc. In the INPUT TEST mode, check such input devices as each SW, V. R. , etc. In the MONITOR ADJUSTMENT mode, check to see if the MONITOR adjustment is appropriately made. Check such data as game play time and histogram to adjust the difficulty level, etc. REFERENCE SECTIONS 9-2 F, G, 9-3 D 9-2 C, 9-3 B 9-3 C 9-2 B, J 9-2 B, J MEMORY PERIODIC SERVICING 9-2 B, J 9-2 F, G, 9-3 D 9-2 C, 9-3 B 9-3 C CONTROL SYSTEM 9-2 C, 9-3 B 9-3 E 10 MONITOR IC BOARD DATA CHECK 9-2 E 11 9-2 B, J 9-2 D 9-2 H, 9-3 F 33 9 - 1 SWITCH UNIT AND COIN METER Never touch places other than those specified. Touching places not specified can cause electric shock and short circuit hazards. STOP IMPORTANT Adjust to the optimum sound volume by considering the environmental requirements of the installation location. If the COIN METER and the game board are electrically disconnected, game play is not /possible. Volumes for the speakers on the right/left of both the monitor and the seat's backrest SPEAKER Sound Volume for the woofer at the player's feet. WOOFER SWITCH UNIT Open the coin chute door, and the switch unit shown will appear. The function of each SW is as follows: SWITCHES FOR THE LEFT SIDE PLAYER SWITCHES FOR THE RIGHT SIDE PLAYER SPEAKER WOOFER LEFT PLAYER TEST RIGHT PLAYER SERVICE DEMAG. FIG. 1 a SWITCH UNIT TEST BUTTON: TEST For the handling of the TEST button, refer to the following pages. Eliminates the on-screen color unevenness due to magnetization of CRT. First use this SW before performing the monitor's color adjustment. SERVICE BUTTON: SERVICE DEMAG. DEMAGNETIZER BUTTON: COIN METER Open the Cashbox Door by using the key to have the Coin Meter appear underneath the Cashbox. COIN METER1 (Left side) Counts the number of coins into 1P side. COIN METER2 (Right side) Counts the number of coins into 2P side. FIG. SYSTEM TEST MODE MENU Press TEST button to enter the TEST MODE, and the following Menu screen will be displayed. SYSTEM MENU XXXXXXXX VERSION RAM TEST JVS TEST SOUND TEST C. R. T. TEST SYSTEM ASSIGNMENTS COIN ASSIGNMENTS BOOKKEEPING BACKUP DATA CLEAR ROMBD TEST CLOCK SETTING GAME TEST MODE > EXIT SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON Press SERVICE button to move the arrow (>) to the desired item and select with TEST button. Bring the arrow to EXIT and press TEST button to return to the GAME Mode. B. RAM TEST This allows for checking the functioning of the RAM on the Game BD. During the test, "CHECKING" is displayed at the right-hand side of the screen. [. . . ] 601-0460 HRT-60012 HRT-60013 POD-61015 POD-61016 600-6972-1050 600-6972-1600 DESCRIPTION PLASTIC TIE BELT 100 MM WH FRONT SPEAKER EXT WH BILLBOARD CONTROL WIRE HARN DC PWR EXT B WIRE HARN COIN CHUTE EXT WIRE HARN EARTH ID5 1050MM WIRE HARN EARTH ID5 1600MM 110 20 ASSY MAIN BASE 1P (HRT-1100) (D-1/2) FAN TORQUE M6 8. 4N·m M8 19. 5N·m FAN 111 BOTH SIDES 20 ASSY MAIN BASE 1P (HRT-1100) ITEM NO. 1 2 3 4 5 6 7 8 9 10 101 102 103 104 201 202 203 204 205 206 207 208 209 210 211 301 302 303 304 PART NO. POD-1120 HRT-1600 HRT-4000 HRT-4100 HRT-0400 VOT-1101X RAL-2007 RAL-2008 HRT-1101 HRT-1102 260-0011-02 280-5009-01 280-5275-SR10 280-5169 000-P00425-W 068-441616 050-H00500 030-000616-SB 060-F00600-0B 060-F00800-0B 000-P00350-W 030-000825-SB 000-P00408-WB 060-S00500 060-F00500 600-6972-0150 600-6275-0200 HRT-60002 HRT-6003 DESCRIPTION ASSY BASE BOX ASSY SEAT ASSY MAIN BD BASE ASSY PWR SPLY AC UNIT MAIN FOOT BASE RUBBER HOLDER R TWIN RUBBER HOLDER L TWIN STICKER BASE BOX STICKER BASE LID AXIAL FLOW FAN AC100V 50-60HZ CORD CLAMP 21 CORD CLAMP SR10 CORD CLAMP TL-20S M SCR PH W/FS M4 X 25 FLT WSHR 4. 4-16 X 1. 6 HEX NUT M5 HEX BLT W/S BLK M6 X 16 FLT WSHR BLK M6 FLT WSHR BLK M8 M SCR PH W/FS M3 X 50 HEX BLT W/S BLK M8 X 25 M SCR PH W/FS BLK M4 X 8 SPR WSHR M5 FLT WSHR M5 WIRE HARN EARTH ID5 0150MM ASSY FIBER CABLE 5 0200CM WH AC100V EXT ASSY WIRE DC (D-2/2) 112 21 ASSY MAIN BASE 2P (HRT-1200) (D-1/2) FAN TORQUE M6 8. 4N·m M8 19. 5N·m FAN 113 BOTH SIDES 21 ASSY MAIN BASE 2P (HRT-1200) ITEM NO. 1 2 3 4 5 6 7 8 9 10 101 102 103 104 201 202 203 204 205 206 207 208 209 210 211 301 302 303 304 PART NO. [. . . ]