User manual SEGA OUTRUN 2_SP SDX

[. . . ] 420-6958-01 1ST PRINTING OUTRUN 2 SPECIAL TOURS SDX OWNER'S MANUAL 420-6958-01 OWNER'S MANUAL Nissay Aroma Building, 5-37-1, Kamata, Ohta-ku, Tokyo 144-8721, Japan Phone: +81-3-5480-6582 Facsimile: +81-3-5480-6584 © SEGA IMPORTANT · Before using this product, read this manual carefully to understand the contents herein stated. · After reading this manual, be sure to keep it near the product or in a convenient place for easy reference when necessary. TABLE OF CONTENTS BEFORE USING THE PRODUCT, BE SURE TO READ THE FOLLOWING: TABLE OF CONTENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii HANDLING PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] While performing the work of fastening the screws, make sure to support the vertical duct firmly. Also, please note that the dimensions of the screws used for this task are different than that of the screw used for the earth wire terminal. 6 ASSEMBLY AND INSTALLATION VERTICAL DUCT FIG. 6-13r Upper rear side of 1P DLP projector Lower rear side of 1P DLP projector Connect the vertical duct wiring connector to the speaker box L wiring connector. There are four connectors. Pass the wiring inside the billboard side cover L duct, and fasten with the cord clamp inside the duct. Secure the wiring firmly with the cord clamp so that no dead weight is applied directly to the wiring. This earth wire is connected to the back of the ranking board. 94 FIG. 6-13s Attach the billboard side cover L duct to the end duct cover over the vertical duct. The screws have flat and spring washers attached. 6 ASSEMBLY AND INSTALLATION END DUCT COVER FIG. 6-13t Remove the billboard electric cover on the back of the ranking board. 6-13u 95 6 ASSEMBLY AND INSTALLATION There is a plate for fastening the earth wire terminals inside the billboard electric. Fasten the terminals of four earth wires, which are inside the duct cover, to open screw holes. There are two earth wires from the side of the LCD monitor, one from the speaker box L, and one inside the vertical duct wiring. Tighten the earth wire terminals one at a time, and not all at the same time. Make sure to always use flat and spring washers with the screws. FIG. 6-13v Attach duct covers to the billboard electric cover that was removed. Be careful not to catch the wiring. 96 14 ATTACHING THE CONTROL TOWER Attach the control tower to the left side of the 1P DLP projector. The control tower will be controlled by an attendant during operation of the product. To ensure safe operation, make sure to provide ample work space for the attendant. Place the control tower close to the left side of the 1P DLP projector, but make sure they do not come in contact with one another. Leave an opening about 10 cm between them. 6 ASSEMBLY AND INSTALLATION FIG. 6-14a Pull out the wiring from the 1P DLP base side and the vertical duct. FIG. 6-14b 97 Connect all of the connectors of the wiring pulled out from the DLP base to the control tower connectors. Connect the yellow connectors in the order of 1, 2, 3, and 4 from the left. 6 ASSEMBLY AND INSTALLATION FIG. [. . . ] Confirm that it is an "Error 22. " If it is an "Error 22, " continue with the following procedures. If it is not an "Error 22, " refer to the LINDBERGH service manual for instructions. Remove 1 resin-head screw, and then remove DVD DRIVE case lid. FIG. 18-3h Press the DVD DRIVE switch and the tray returns to its original position. After verifying that there are no people in the area of the ride, reset the power. [. . . ]