User manual SEGA NAOMI_LINDBERGH VT3 REV1

[. . . ] RND-0073 REV 1 SERVICE MANUAL Incorporating UPRIGHT TYPE Before using this product, read this SERVICE MANUAL carefully to understand the contents stated herein. After reading this manual, be sure to keep it available nearby the product or somewhere convenient in order to be able to refer to it whenever necessary. Manufactured in the UK by CONTENTS BEFORE USING THIS PRODUCT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 INSPECTIONS IMMEDIATELY AFTER TRANSPORTING THE PRODUCT TO THE LOCATION . 2 2. INTRODUCTION TO THIS SERVICE MANUAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 3. INSTALLATION AND MAINTENANCE INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 3. 1. [. . . ] Turn the Filter Board to face the side with the three honeycomb buffers. Packing it in the opposite direction may cause damage to the Filter Board. Insert corrugated cardboard into the space between the lateral honeycomb buffers of the bottom surface cushioning material and stow the AVIP cable inside. Place the Chihiro Board wrapped in the bottom surface cushioning material into the carton box. Place the upper surface cushioning material on top of the Chihiro Board. Be sure to align it in the right direction, as it will not fit otherwise. Close the top of the carton box and seal it tightly with adhesive tape. Place the LINDBERGH into the outer packaging and fold around Game Board as shown. Slide the unit into the carton and seal. 9 3. 5. ASSEMBLY INSTRUCTIONS · Perform the assembly by following the procedure herein stated. Failure to comply with the instructions, for example, inserting the plug into an outlet at a stage not mentioned in this manual can cause an electric shock · Assembling should be performed as per this manual. Since this is a complex machine, erroneous assembling can cause damage to the machine, or malfunction to occur. · Do not attempt to complete this work alone, a minimum of 2 people are required. · Only QUALIFIED SERVICE PERSONNEL should carry out assembly. When carrying out the assembly work, follow the procedure in the following three item sequence: STEP 1 STEP 2 STEP 3 INSTALLING THE BILLBOARD SECURING IN PLACE (LEG ADJUSTER ADJUSTMENT) CONNECTION TO THE POWER SUPPLY Note that the parts contained within the installation kit are required for the assembly work. The following tools will be required when installing this machine: WRENCH (FOR M4 TAMPERPROOF SCREW) 10 3. 5. 1. INSTALLING THE BILLBOARD · Only QUALIFIED SERVICE PERSONNEL should carry out this operation. 1. SECURING IN PLACE (LEG ADJUSTER ADJUSTMENT) · Make sure all of the leg adjusters are in contact with the floor. This operation requires 2 people. · This operation should only be carried out by QUALIFIED SERVICE PERSONNEL. This machine has four castors and two leg adjusters. When the installation position is decided, unscrew the leg adjusters so that they raise both front castors 7mm from the floor. Unscrew the adjusters until they are in contact the floor, and use a wrench to turn them further until the front castors are raised approximately 7mm above the floor. Tighten the locknut on the leg adjusters upwards to lock the legs in position. Ensure adequate ventilation is maintained as detailed below: 12 3. 5. 3. CONNECTION TO THE POWER SUPPLY · Be sure that the machine is not connected to the mains supply before attempting this operation · This operation should only be carried out by QUALIFIED SERVICE PERSONNEL. The AC Unit is located on the right hand side of the base unit, when viewing the screen (as shown in section 3. 3). [. . . ] 1 2 3 101 102 103 104 106 107 201 301 302 303 304 305 PART NUMBER NOA-1451UK 837-13551-92 NOA-1117UK 838-13739 280-A02048-PM 280-A01248-PM 280-A00900-A 280-L00940-PM 280-L00709-OS 000-P00320-W NOA-60021 NOA-60022UK NOA-60023 NOA-60024 NOA-60025 QTY 1 1 1 1 1 5 2 3 3 7 1 1 1 1 1 DESCRIPTION I/O BASE I/O CONTROL BD FOR JVS WATER GUARD SW BD NAOMICABINET ROUTER TWIST D20 SO4. 8 P ROUTER TWIST D12 SO4. 8 P ROUTER TWIST D9 ADH STANDOFF 9L 4mm HOLE PAN STANDOFF 7OD 4ID 9L M3X20 MSCR POSI PAN W/FS WIRE HARN ANALOG CONTROL WIRE HARN SW CONTROL WIRE HARN I/O BD PWR WIRE HARN SPEAKER L WIRE HARN SPEAKER R COMPONENT REFERENCE (1)-1 [NOT SHOWN] [NOT SHOWN] [NOT SHOWN] (MONITOR REMOTE BOARD)-3 (101)-3 (2)-4, (101)-3 [NOT SHOWN] [NOT SHOWN] [NOT SHOWN] [NOT SHOWN] [NOT SHOWN] 46 8. 9. NOA-1480UK ASSY COIN MECH No. 1 2 3 4 101 103 104 202 203 204 205 PART NUMBER NOA-1481XUK NOA-1482 NOA-1483 NOA-1484UK 220-5086-AUK 220-5086-CUK 000-F00408 000-P00308 060-S00300 060-L00300 060-F00400 QTY 1 1 1 2 1 2 5 1 1 1 1 DESCRIPTION BASE COIN SELECTOR LINK COIN CHUTE UPPER COIN CHUTE ADHESIVE INSULATING PAD MECH CADDY BASE MECH CLIP M4X8 MSCR CSK PAS M3X8 MSCR PAN PAS M3 WSHR SPR PAS M3 WSHR LOCK PAS M4 WSHR FORM A FLT PAS COMPONENT REFERENCE (3)-2, (101)-3 (2)-1 (2)-1 (2)-1 (2)-1 47 8. 10. 1 2 3 201 202 PART NUMBER NOB-1481UK NOB-1482 NOB-1484 045-0037 000-P00408-W QTY 1 1 1 1 2 DESCRIPTION BASE COIN SELECTOR LINK COIN SELECTOR 220 L HOOK DIA6 SNAP PIN M4X8 MSCR PAN W/FS PAS COMPONENT REFERENCE (3)-2 48 8. 11. 1 3 4 5 6 7 201 202 PART NUMBER NOA-1500UK-S1 NOA-1503 NOA-1504UK NOA-1505 NOA-1506 NOA-1507 000-P00412-W 012-P03516 QTY 1 1 1 1 2 1 5 4 DESCRIPTION ASSY FRONT PANEL NF LIGHT COVER PRISM PLATE LID GCS LID VMS EMBLEM NAOMI M4X12 MSCR POSI PAN W/FS N6X5/8" S/TAP PAN PAS COMPONENT REFERENCE NOA-1501 + NOA-1502X AS AN ASSY CLIP-IN (5)-5 (4)-4 49 8. 12. [. . . ]