User manual SEGA MANXTT

[. . . ] Herein, explanations which require special attention are enclosed with dual lines. Depending on the potentially hazardous degrees, the terms of DANGER, WARNING, CAUTION, etc. Be sure to understand the contents of the displays before reading the text. Indicates that mishandling the product by disregarding this pictograph will cause severe injury or death. [. . . ] The GAME TEST MODE screen reappears. 40 EXPLANATION OF TEST AND DATA DISPLAY 9-3-5 DRIVE BD TEST This screen is for checking the steering wheel's force feedback. Periodically use this screen to check that the steering wheel's force feedback is operating normally. 1 On the GAME TEST MODE screen, select DRIVE BD TEST and press the TEST Button. The DRIVE BD TEST screen appears. DRIVE BD TEST SPRING CLUTCH CENTERING UNCENTERING ROLL LEFT ROLL RIGHT ->EXIT STEERING VOL *--*--*--*--*--**H 12 9 DIP SWITCH 3 4 5 6 7 8 OFF OFF OFF OFF OFF OFF OFF OFF SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON Move the cursor up and down with the SERVICE Button or the VR1 (red) and VR2 (blue) buttons. The VR3 (yellow) and VR4 (green) buttons can be used to increase or decrease the force transmitted to the steering wheel. 2 SPRING Each item is explained below. Check to make sure the values are as follows: Appropriate volume values: 2DH or lower 7D - 83H D3H or higher (Left) (Center) (Right) Display the setting status of DIP SW on the DRIVE BD. CLUTCH CENTERING UNCENTERING ROLL LEFT ROLL RIGHT STEERING VOL DIP SW EXPLANATION OF TEST AND DATA DISPLAY 41 3 1 OFF ON OFF ON OFF ON ON 4 OFF ON <DIP SW Settings Chart> The DIP SW settings on the drive board can be used to set the steering wheel resistance, select whether to perform the power on check, etc. Refer to "19-2" when changing the settings. DIP SW Settings: The grayed out settings are the defaults 2 OFF OFF ON ON OFF OFF ON Function Perform power on check. 3 OFF OFF OFF OFF ON ON ON Heavy Function Light 9 Always recycle the power after making changes to the DIP SW settings. If the recoil becomes weak, change the DIP SW settings. 4 5 <Drive Board Error Display> If a problem occurs on the drive board, the test will not work when selecting DRIVE BD TEST on the GAME TEST MODE screen. If this happens, an error number will be displayed on the 7-segment display on the drive board. If a power on check error occurs, the 7-segment display will flash continuously. First, check to make sure there is nothing wrong with the volume, motor, clutch, etc. - Do not use a chemical detergent containing an abradant, powder or bleaching agent. DonotruborscratchtheLCDmonitorscreenwithharditemssuchasbrushes, scrub brush, etc. Donotsticktape, stickersoranythingelseontothescreen. Anykindofadhesive may damage the surface of the screen. Clean the LCD monitor screen once a week. LCD MONITOR 47 10-2 ADJUSTING THE LCD MONITOR Avoidanyunnecessaryadjustment. Adjustingthemonitormayleadtoelectric shock or cause short circuits. If a mistake is made while performing adjustments, the game may stop operating. Becarefulnottodamagethewires. Damagedwiresmaycauseelectricshockor shortcircuitorpresentariskoffire. Donottouchanypartsthatarenotspecifiedinthesedirections. Touching unspecifiedlocationsmayleadtoelectricshockorcauseshortcircuits. Besuretoperformappropriateadjustmentofthemonitor(LCD). Foroperation ofthismachine, donotleavemonitor'sflickeringordeviationasis. Failure toobservethiscanhaveabadinfluenceupontheplayers'orthecustomers' physical conditions. Whenattachingorremovingdoors, becarefulthatyourhandorfingerdoesnot get caught in anything. 10 48 LCD MONITOR How to Access the Adjustment Board 1 2 Turn off the power switch of the cabinet. Remove the 2 truss screws and take off the upper door on the back side of the cabinet. 10 TRUSS SCREW (2), black M4 x 30, w/flat & spring washers, large flat washer used 3 There is an adjustment board on the bottom of the LCD monitor. A long wire is connected to the adjustment board. AJUSTMENT BOARD 4 Take the adjustment board out from underneath the LCD, pull it in front of the monitor, and make adjustments while watching the screen. When taking out and replacing the adjustment board, be careful not to get the wires caught on anything, pinch them, or otherwise damage them. LCD MONITOR 49 Description of Functions 6 1 2 3 4 5 6 5 4 3 2 1 Power LED MODE "+" "-" MENU/ENTER (EXIT) AUTO Green Light is with the signal; Red Light is signal out of range or no signal. Press the button to adjust the increasing value of selected OSD control item. [. . . ] 601-0460 SRC-60013X SRC-60014 SRC-60015 SRC-60016X SRC-60017X DESCRIPTION PLASTIC TIE BELT 100 M/M WH STEERING MON CABI WH 4SPEED SHIFTER MON CABI WH VR BUTTON MON CABI WH SPEAKER MON CABI WH LEADER LED MON CABI NOTE 21 132 PARTS LIST (19) SRC-6002 ASSY WIRE MON CABI AC This is comprised of the following wire harnesses. 601-0460 SRC-60018X SRC-60019X 600-6972-1650 DESCRIPTION PLASTIC TIE BELT 100 M/M WH AC FL & FAN IN MON CABI WH DRIVE BD CLUTCH PANEL IN WIRE HARN EARTH ID5 1650MM NOTE 21 207 4 206 4 4 1 10 1 210 4 101 1 102 1 208 4 209 4 (20) SRC-1500 ASSY MAIN BASE Fan wind SEE B 205 6 213 2 8 1 3 1 212 2 211 2 201 4 2 1 9 1 7 1 204 6 207 4 206 4 SEE A EARTH SEE B 11 1 12 (Opposite side ) 1 Fastening torque: M6 8. 4 N. m M8 19. 5 N. m SEE A (D-1/2) 1 1 5 1 202 2 203 2 202 2 6 1 PARTS LIST 203 2 133 21 134 PARTS LIST (20) SRC-1500 ASSY MAIN BASE ITEM NO. 1 2 3 4 5 6 7 8 9 10 11 12 101 102 103 104 201 202 203 204 205 206 207 208 209 210 211 212 213 301 302 303 304 305 PART NO. SRC-1520 SRC-1540 SRC-1600 SPG-2200-02 SPG-2200-02-CN SRC-4500 SRC-4600 SRC-1501 RAL-2007X RAL-2008X SRC-1502X SRC-1503 SRC-1504 260-0116 601-8543 280-5009-02 280-7881 000-P00408-WB 000-P00425-W 068-441616 030-000616-SB 060-F00600-0B 030-000825-SB 060-F00800-0B 000-P00350-WB 050-F00300 000-T00512-0C 050-H00400 060-S00400 060-F00400 600-7009-3000 SRC-6003 SRC-6004 SRC-60004X SRC-60054 DESCRIPTION ASSY BASE BOX AC UNIT ASSY ADJUSTABLE SEAT ASSY ACCEL&BRAKE ASSY ACCEL&BRAKE CHINA ASSY MAIN BD ASSY ELEC BD PEDAL BASE RUBBER HOLDER R TWIN RUBBER HOLDER L TWIN BASE LID F STICKER MAIN BASE L STICKER MAIN BASE R FAN AC115V A1123-HBT-GN FAN GUARD CORD CLAMP 21 CN CORD CLAMP SR10 CN M SCR PH W/FS BLK M4x8 M SCR PH W/FS M4x25 FLT WSHR 4. 4-16x1. 6 HEX BLT W/S BLK M6x16 FLT WSHR BLK M6 HEX BLT W/S BLK M8x25 FLT WSHR BLK M8 M SCR PH W/FS BLK M3x50 FLG NUT M3 M SCR TH CRM M5x12 HEX NUT M4 SPR WSHR M4 FLT WSHR M4 ASSY RGB CA D-SUB 15P 3000MM ASSY WIRE MAIN BASE DC ASSY WIRE MAIN BASE AC WH SEAT & WOOFER MAIN BASE WH AC WDE SW & FAN IN NOTE (D-2/2) OR 21 PARTS LIST 135 (21) SRC-1520 ASSY BASE BOX 2 1 202 4 203 4 1 1 4 1 201 4 101 1 3 1 ITEM NO. [. . . ]