User manual SEGA JAMBO SAFARI

[. . . ] Sellers sole liability in the event a warranted part described above fails shall be, at its option, to replace or repair the defective part during the warranty period. Should the Seller determine, by inspection that the product was caused by Accident, Misuse, Neglect, Alteration, Improper Repair, Installation or Testing, the warranty offered will be null and void. Under no circumstances is the Seller responsible for any loss of profits, loss of use, or other damages. This shall be the exclusive written Warranty of the original purchaser expressed in lieu of all other warranties expressed or implied. Under no circumstance shall it extend beyond the period of time listed above. TABLE OF CONTENTS INTRODUCTION OF THE OWNERS MANUAL GENERAL PRECAUTIONS 1. [. . . ] MEMORY Choose MEMORY TEST in the MENU mode to allow the MEMORY test to be performed. In this test, PROGRAM RAMs, ROMs, and ICs on the IC Board are checked. In the MONITOR ADJUSTMENT mode, check to see if the MONITOR adjustment is appropriately made. Check such data as game play time and histogram to adjust the difficulty level, etc 7 - 3, 7 - 4 7 - 10, 7 - l1 7-6 7-7 7-6 8 12 7-2 7-8 7 - 15 P CONTROL SYSTEM MONITOR IC BOARD DATA CHECK 22 7 - 1 SWITCH UNIT AND COIN METER Never touch places other than those specified. Touching places not specified can cause electric shock and short circuit. Adjust to the optimum sound volume by considering the environmental requirements of the installation location. If the COIN METER and the game board are electrically disconnected, game play is not possible. Open COIN CHUTE DOOR, and the switch unit shown appears. The function of each switch is as follows: SWITCH UNIT 1 SOUND VOLUME Controls the speaker volume of the right/left speakers. 2 TEST BUTTON (TEST SW) For the handling of the TEST BUTTON, refer to the section on test mode. 3 SERVICE BUTTON (SERVICE SW) Gives credits without registering on the coin meter. 23 7 - 2 SYSTEM TEST MODE The contents of setings chnaged in the TEST mode are stored when the TEST mode is finished from EXIT in the MENU mode. If the power is turned off before the TEST mode is finished, the contents of setting chnage become ineffective. Executing "BACKUP DATA CLEAR" in the SYSTEM TEST MODE does not clear the BOOKKEEPING data in the GAME TEST MODE. Entering the TEST mode clears fractional number of coins less than one credit and BONUS ADDER data. The SYSTEM TEST mode mainly allows for IC Board functioning check, monitor adjustment, coin assignments, etc. The following assignments, however, should be designated for this product. Check if the CROSSHATCH FRAME LINE goes out of the screen and if the crosshatch lines are distorted. The color bar of each of the 4 colors, i. e. , red, green, blue, and white, is the darkest at the extreme left and becomes brighter towards the extreme right. TEST to cause the MONITOR to display the screen shown left, allowing MONITOR adjustment status to be checked. 7 - 8 VOLUME SETTING When VOLUME SETTING is selected, the following appears on the screen and each operating unit's Volume can be set. If the operability is unsatisfactory, or when the Volume is adjusted or replaced, set the Volume in this mode. The 3 kinds of Volume Settings for HANDLE, ACCEL, and BRAKE are to be set. value for each and the HANDLE'S CENTER value are to be set as applicable. VOLUME SETTING HANDLE SETTING AD0:7bH CENTER 7bH LEFT MAX 1aH <----> a4H RIGHT MAX ACCEL SETTING AD1:30H MIN 31H <----> c0H MAX BRAKE SETTING AD2:38H MIN 39H <--->bcH MAX 1 Press the SERVICE button to select the Volume value to be changed. Press the TEST button to cause the characters of the selected Volume value to turn red. Press the SERVICE buton to select EXIT, and press the TEST button to return to the MENU mode. At the same time the VOLUME SETTING is finished, the input values are stored as the Max. values. 2 3 >EXIT 4 SELECT WITH SERVICE BUTTON PRESS TEST BUTTON TO EXIT FIG. 7. 8 VOLUME SETTING 27 7 - 9 GAME ASSIGNMENTS Selecting the GAME ASSIGNMENTS in the MENU mode causes the present game settings to be displayed and also the game settings changes (game difficulty, etc. ) can be made. [. . . ] Depending on the cause of the fuse blowing, using the fuse as is blown can cause generation of heat resulting in fire. Incline the Seat and remove the Base Lid to view the Base interior. When replacing the fuse, be sure to use the specified one. 50 16 - 3 COMPOSITION OF GAME BOARD Ensure that the DIP SW setting is performed as designated as designated. Failure to observe thisw may cause functioning not suitable for tyhe operation, or malfunctioning. ASSY CASE NAO USA (840-0002D-01) :USA DIP SW SETTING IN the product, set all of the DIP SWes to OFF. 51 17. 1 2 6 7 8 9 10 11 12 13 14 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 PART NO. [. . . ]