User manual SEGA INITIAL D 2 TWIN

[. . . ] Be sure to keep this manual nearby the product or elsewhere convenient for referring to it when necessary. Herein, explanations which require special attention are enclosed with dual lines. Depending on the potentially hazardous degrees, the terms of WARNING, CAUTION, etc. Be sure to understand the contents of the displays before reading the text. [. . . ] Gives credits without registering on the coin meter. DEMAGNETIZER SWITCH: Eliminates the on-screen color unevenness due to magnetization of (DEMAG. ) CRT. First use this SW before performing the monitor's color adjustment. COIN METER Open the Cashbox Door by using the key to have the Coin Meter appear underneath the Cashbox. COIN METER FIG. 1 b www. seuservice. com 44 10-2 SYSTEM TEST MODE STOP IMPORTANT! The contents of settings changed in the TEST mode are stored when the test mode is finished from EXIT in the menu mode. If the power is turned off before the TEST mode is finished, the contents of setting change become ineffective. Executing "BACKUP DATA CLEAR" in the SYSTEM TEST MODE does not clear the BOOKKEEPING data in the GAME TEST mode. Entering the TEST mode clears fractional number of coins less than one credit and BONUS ADDER data. If setting not specified is performed for operation, proper function of this product may not be obtained. In the SYSTEM TEST MODE, IC BD functioning can be checked, the monitor adjusted, and the coin setting performed. Note that the setting of the following items need to be performed in accordance with the instruction given. CABINET TYPE MONITOR TYPE SERVICE TYPE COIN CHUTE TYPE NETWORK TYPE : : : : : 1 PLAYER(S) HORIZONTAL COMMON COMMON NONE The SEQUENCE SETTING items of COIN/CREDIT SETTING are as follows. SEQUENCE SETTING SEQUENCE 1: Number of credits required for starting the game. When the RIGHT menu item is ON, the STEERING rotates to the right as far as possible and then stops. Press the SERVICE Button again to turn it OFF and release control of the STEERING. When the LEFT menu item is ON, the STEERING rotates to the left as far as possible and then stops. Press the SERVICE Button again to turn it OFF and release control of the STEERING. Move the cursor to EXIT and press the TEST Button to return to the Game Test Menu screen. 49 www. seuservice. com E. INPUT ASSIGNMENTS Select INPUT ASSIGNMENTS to display the following screen. GAME TEST MODE INPUT ASSIGNMENTS STEERING: XXX (DEFAULT = 0) ACCEL : XXX (DEFAULT = 0) BRAKE : XXX (DEFAULT = 0) DEFAULT SETTING -> EXIT SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON FIG. 3 ea INPUT ASSIGNMENTS Screen You can adjust each of the menu items by moving the cursor to the menu item and pressing the TEST Button. STEERING: Make adjustments to STEERING Press the TEST Button to display the following screen. When the "0" displayed is not exactly aligned with the "^" mark above CENTER, use the cursor to select RIGHT or LEFT and move the "0" until it is displayed directly above the "^" mark. Move the cursor to RIGHT and press the TEST Button to move the "0" to the right. Each time you press the TEST Button, "0" moves slightly to the right. [. . . ] APC-1561 130-5156-01 000-P00512-W DESCRIPTION SPEAKER BRKT SPEAKER BOX 8OHM 20W VA1 M SCR PH W/FS M5×12 NOTE 97 www. seuservice. com ASSY SPEAKER L (APC-1560) ITEM NO. APC-1561 130-5156-01 000-P00512-W DESCRIPTION SPEAKER BRKT SPEAKER BOX 8OHM 20W VA1 M SCR PH W/FS M5×12 NOTE www. seuservice. com 98 ASSY CONTROL PANEL (TOF-2000) 99 www. seuservice. com Attached to 6 ASSY CONTROL PANEL (TOF-2000) ITEM NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 101 102 103 104 105 201 202 203 204 205 206 207 208 209 PART NO. TOF-2001 TOF-2500 TOF-2002 TOF-2003 TOF-2004 TOF-2005 TOF-2006 TOF-2007 TOF-2008 TOF-2009 TOF-2150 601-11097 601-11098 TOF-2010 280-5169 280-0419 610-0408-91 601-0460 280-5009-01 030-000820-S 060-F00800 000-T00408-0B 000-P00410-W 008-T00512-0B 000-T00410-0C 000-T00408-0B 050-F01200 FAS-290015 DESCRIPTION CONTROL PANEL BRKT ASSY HANDLE MECHA HANDLE COLLAR CONTROL PANEL COVER SHIFT COVER UPPER SHIFT COVER LOWER COVER HOLDER CUSHION CTRL PNL PLATE WIRE HOLDER ASSY SW PLATE STEERING WHEEL 340 STEERING EMBLEM 340 STICKER STEERING EMBLEM CORD CLAMP TL-20S HARNESS LUG UP/DOWN SHIFTER AL PLASTIC TIE BELT 100 MM CORD CLAMP 21 HEX BLT W/S FLT WSHR M SCR TH BLK M SCR PH W/FS TMP PRF SCR TH BLK M SCR TH CRM M SCR TH BLK M4×8 FLG NUT M12 HEX SKT SCR FH BLK M4×12 NOTE www. seuservice. com 100 Plated yellow ASSY HANDLE MECHA (TOF-2500) Plated black (After installing 6 ) 101 www. seuservice. com Fastening Torque: M3: 0. 74N. m. M4: 1. 8N. m. M6: 5. 6N. m. M8: 17. 4N. m ASSY HANDLE MECHA (TOF-2500) ITEM NO. [. . . ]