User manual SEGA HOUSE OF THE DEAD 3 UPRIGHT

[. . . ] 420-6742-02UK REV 1 SERVICE MANUAL UPRIGHT TYPE Before using this product, read this SERVICE MANUAL carefully to understand the contents stated herein. After reading this manual, be sure to keep it available nearby the product or somewhere convenient in order to be able to refer to it whenever necessary. BEFORE USING THIS PRODUCT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1. 1. INSPECTIONS IMMEDIATELY AFTER TRANSPORTING THE PRODUCT TO THE LOCATION . 2 2. [. . . ] Remove the control panel cover as shown by removing the 5 screws holding it in position. Carefully lift the control panel cover up until it is possible to disconnect the wire harness plugs attaching the start switches to the cabinet. Turn the control panel cover over and remove the micro switch from the start switch as shown below. GAME BOARD · Turn off the mains power and remove the power cord before opening the machine. · To prevent risk of shock or fire, be careful not to damage any wiring. · The GAME BOARD should not require any work to be carried out upon it. All settings and tests can be achieved without access to the GAME BOARD. · Take anti-static precautions to avoid damaging the electronic parts. · All work to be carried out by QUALIFIED SERVICE PERSONNEL The GD-ROM Service Manual supplied with this product instructs you to remove the Key Chip when shipping the Game Board. However, this product employs a dedicated Game Board, therefore do not disassemble the Game Board, or remove the Key Chip. 3. 14. 1. Disconnect all harnesses linking the Game Board assembly to the cabinet. Remove the two M4 wing bolts and carefully withdraw the assembly upwards and out through the service opening (see following page). 37 5. REMOVING THE GD-ROM DRIVE Take out the ASSY MAIN BD from the cabinet and remove the GD-ROM Drive from the ASSY MAIN BD as follows: 1. Following the above procedure (steps 1 to 5), take out the ASSY MAIN BD. Remove the GD cable connector and the power cord connector from the GD-ROM Drive. 2. TROUBLESHOOTING · Only QUALIFIED SERVICE PERSONNEL should carry out these procedures. If a problem occurs, first check the wiring connections. PROBLEMS CAUSE COUNTERMEASURES Firmly insert the plug into the outlet. When the main switch The power is not ON. is turned ON, the machine is not activated Incorrect power source/voltage. fuse) was activated due to an instantaneous overcurrent. Make sure that the power supply/voltage are correct. First, remove the cause of overcurrent and reinstate the circuit protection device to its original status. Then identify the cause of the fault on the item which caused the overcurrent & fix. The colour image on Incorrect monitor adjustment. the screen is incorrect The on-screen image of the monitor sways and/or shrinks Sound is not emitted The power source and voltage are not correct. SEE SECTION 6. 3. 7 Check connector connection from Base to Speaker Adjust the gun sighting alignment. [. . . ] HDT-5150UK ASSY GUN HOLSTER L U/R Item 1 2 3 7 9 11 201 202 203 204 Component Part HDT-2181UK HDT-5151UK HDT-2182UK HDT-2187UK HDT-2197UK HDT-5153UK 000-T00512-0B 008-P00620-0B 050-U00600 068-651616-0B Qty. 1 1 1 1 1 1 8 4 1 1 Description GUN HOLSTER GUN HOLSTER SUPPORT L GUN HOLSTER SUPPORT STICKER HOLSTER SIDE GUN CUSHION GUN TETHER UR M5X12 MSCR TH BLK M6X20 TMP PRF TH BLK M6 NUT NYLOK PAS M6 WSHR 16OD FLT BLK Component Reference (3)-8 (2)-4 (2)-1 (2)-1 103 9. 13. HDT-5170UK ASSY GUN HOLSTER R U/R Item 1 2 3 7 9 11 201 202 203 204 Component Part HDT-2181UK HDT-5152UK HDT-2182UK HDT-2187UK HDT-2197UK HDT-5153UK 000-T00512-0B 008-P00620-0B 050-U00600 068-651616-0B Qty. 1 1 1 1 1 1 8 4 1 1 Description GUN HOLSTER GUN HOLSTER SUPPORT R GUN HOLSTER SUPPORT STICKER HOLSTER SIDE GUN CUSHION GUN TETHER UR M5X12 MSCR TH BLK M6X20 TMP PRF TH BLK M6 NUT NYLOK PAS M6 WSHR 16OD FLT BLK Component Reference (3)-8 (2)-4 (2)-1 (2)-1 104 9. 14. [. . . ]