User manual SEGA HOUSE OF THE DEAD 3 DX

[. . . ] 420-6742-01UK REV 0 SERVICE MANUAL DELUXE TYPE Before using this product, read this SERVICE MANUAL carefully to understand the contents stated herein. After reading this manual, be sure to keep it available nearby the product or somewhere convenient in order to be able to refer to it whenever necessary. BEFORE USING THIS PRODUCT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1. 1. INSPECTIONS IMMEDIATELY AFTER TRANSPORTING THE PRODUCT TO THE LOCATION . . 2 2. [. . . ] Therefore, remove the 1 screw on the right half of the cover first, before removing the rest of the screws, with the right half downmost. Remove the 2 tapping screws, and remove the microswitch from the slide mechanism. Operate the trigger and grip, and make sure that the microswitch turns ON/OFF correctly. REPLACING THE SENSOR UNIT Follow instructions 1. of "Replacing the Microswitch" up to removing the left side cover. Remove the tapping screw, if required to gain better access. 33 3. 15. GAMEBOARD · Turn off the mains power and remove the power cord before opening the machine. · To prevent risk of shock or fire, be careful not to damage any wiring. · The GAME BOARD should not require any work to be carried out upon it. All settings and tests can be achieved without access to the GAME BOARD. · Take anti-static precautions to avoid damaging the electronic parts. · All work to be carried out by QUALIFIED SERVICE PERSONNEL The GD-ROM Service Manual supplied with this product instructs you to remove the Key Chip when shipping the CHIHIRO Board. However, this product employs a dedicated CHIHIRO Board, therefore do not disassemble the CHIHIRO Board or remove the Key Chip. 3. 15. 1. REMOVING THE BOARD 1. Disconnect all harnesses connected to the CHIHIRO Main Board assembly as circled below. 34 4. Remove the two screws securing the base to the cabinet and withdraw the main board assembly upwards out of the cabinet. Pull the ASSY MAIN BD out of the Cabinet and set it on a level surface before continuing. Unplug the GD Cable connector on the side of the Media Board on the Chihiro Board. This is because the AVIP Cable is packed with it when the Chihiro Board is transported. Remove the 4 screws and remove the Chihiro Board from the Base. 35 3. 15. 2. REMOVING THE GD-ROM DRIVE Take out the ASSY MAIN BD from the PTV cabinet and remove the GD-ROM Drive from the ASSY MAIN BD as follows: i. Following the above procedure (steps 1 to 5), take out the ASSY MAIN BD. Remove the GD cable connector and the power cord connector from the GD-ROM Drive. 3. To remove the GD-ROM Drive, undo the four screws shown. 36 3. 16. PERIODIC CHECK AND INSPECTION The items listed below require periodic check and maintenance to retain the performance of the machine and ensure safe operation: · Be sure to check annually to see if the power cords are damaged. [. . . ] HDT-2000UK ASSY CTRL PANEL DX Item 1 3 4 101 301 Component Part HDT-2001-A-W HDT-2001-B HDT-2001-C-01UK 509-5712-01S HOD-60020 Qty. 1 1 1 2 1 Description CTRL PNL BLANK W/NUT PLATES BUTTON SHEET DX STICKER CTRL PNL TOP ENG SW PB W/L 6V YELLOW WIRE HARN CONTROL PANEL Component Reference 94 8. 12. 1 2 3 4 5 6 7 8 9 10 101 102 103 104 105 201 202 203 204 301 PART NO. HDT-2120 HDT-2101 HDT-2102 HDT-2103 HDT-2104 HDT-2105 HDT-2106 HDT-2107 HDT-2108 JPT-2030 280-5124-02 280-5124-03 310-5029-D20 509-5080 601-0460 FAS-000092 FAS-000093 FAS-000094 FAS-120023 HDT-60007 DESCRIPTION NOTE ASSY SLIDE MECHA COVER L COVER R SLIDE GRIP L SLIDE GRIP R FRONT SIGHT TRIGGER TRIGGER SPRING STOPPER PIN SENSOR UNIT NYLON CLAMP NK02 NYLON CLAMP NK03 SUMITUBE F D 20MM SW MICRO TYPE (SS-5GL2) PLASTIC TIE BELT 100 MM M SCR PH W/SMALL FS BLK M3·~8 M SCR PH W/SMALL FS BLK M3·~16 M SCR BIND H W/TOOTH BLK M4·~8 TAP SCR P-TITE PH 3·~8 WH CONTROL UNIT 8. 13. [. . . ]