User manual SEGA HOUSE OF THE DEAD 1 UR

[. . . ] INTRODUCTION TO THIS SERVICE MANUAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 3. INSTALLATION AND SERVICE INSTRUCTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 3. 1. HANDLING AND INSTALLATION PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 3. 2. COIN HANDLING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 3. 3. [. . . ] · Do not cut the tie belt securing the wires in the Control Unit (Shotgun). If you cut the tie belt when replacing the wire etc. , be sure to secure the wires using a new tie belt as before · After removing 4 bind screws once, retighten them by using the designated threadlocking agent (Part Number: 090-0012). If the threadlocking agent is not used, the reassembled shotgun may rattle or come apart. Use of other threadlocking agents may cause chemical reactions that could damage the screws or part's surface. In the cases where the gun's operation is not satisfactory or the gun sight deviates from the direction in which the control unit is pointed, the gun's interior parts may have been damaged. Replace the parts by disassembling the gun in the following procedure: Also, be sure to perform sighting check in the test mode when the gun parts are replaced. REPLACING THE MICROSWITCH To replace parts in the Shotgun, it is necessary to separate the two halves of the outer case cover. Internal parts are inserted directly into the right side of the cover, so the procedure should be carried out with the right half downmost. Remove the 2 BIND screws from each side and remove the left and right Slide Grips. To separate the left and right halves of the cover, remove the 3 (M3X8) screws and the 12 (M3X16) screws. Therefore, remove the 1 screw on the right half of the cover first, before removing the rest of the screws, with the right half downmost. Using the product in an unclean condition may cause a fire or electric shock. · Only QUALIFIED SERVICE PERSONNEL should carry out periodic checks. DESCRIPTION MONITOR / PROJECTOR GAME BD INTERIOR POWER SUPPLY CORD CABINET SURFACE CONTROL PANEL CONTROLLER (GUN) WHAT TO CHECK Clean screen Check adjustment Memory Test Game Assignments Clean (Do Not use water jet) Check condition Clean (Do Not use water jet) Lamp operation Check switch operation Clean Check sighting Check switch operation Weekly Monthly Monthly Monthly Annually Annually INTERVAL As required Monthly Monthly As required Weekly Monthly Monthly COIN MECHANISM Check SW (If Fitted) 38 4. HOW TO PLAY Use this section to confirm the machine is operating correctly; if the machine doesn't operate as described there may be a fault. While power is connected, the billboard is continuously lit and demonstration footage and ranking data are displayed on the screen. This `advertise' mode will be accompanied by sound from both speakers unless set otherwise in the TEST mode. The 1P and 2P start buttons have integral lights that flash when a credit is inserted. 39 4. 1. GAME CONTENTS 4. 1. 1. Insert a coin and the credit indicator below the screen will count up. When enough coins have been entered for one play, the "INSERT COIN(S)" message below the screen will change to "PRESS START BUTTON", and both START buttons will flash. A player plays on the left or the right by pressing the start button on that side. When the game starts, the stage title is displayed and a demo plays before switching over to game play. · Life and loaded bullets remaining are shown at the bottom left of the screen for the player on the left (Player 1). Life and loaded bullets remaining are shown at the bottom right of the screen for the player on the right (Player 2). 40 · Firing six rounds empties the weapon and displays the "RELOAD" instruction on the screen. Players load the shotgun clip by pump action. If some bullets remain, pumping the shotgun will fully reload the gun. Reloads with pump action! · Players can defend themselves against knives, oil drums and barrels thrown by enemies by shooting them. [. . . ] 1 2 1 1 1 2 2 1 1 2 1 1 1 1 2 12 8 Description ASSY CTRL PANEL DX HOLDER VTS BOARD HOD GUN HOLDER CABI CASH BOX TUBE CLAMP CONTROL UNIT JOINT PART LID COIN PATH PLATE HOLDER BRKT SIDE BRKT L BLANK SIDE BRKT R BLANK ASSY FENCE L ASSY FENCE R CHAIN BRKT M4X16 MSCR TH BLK M4 WSHR 16OD FLT BLK Component Reference BUBBLE WRAP SEPARATELY BUBBLE WRAP SEPARATELY (1)-8, (7)-4 (1)-8 CONTINUED NEXT PAGE 90 CONTINUED FROM PREVIOUS PAGE ITEM 203 204 207 208 209 210 211 212 301 302 303 304 305 PART NUMBER 008-T00430-0B 000-T00440-0B 000-P00420-W 030-000630-SB 030-000616-SB 060-F00600-0B 000-P00408-W 008-T00408-0C SPY-60014UK SPY-60015 HDT-60002UK 600-9220-44K 600-9040-44K QTY 8 4 9 12 8 8 2 4 1 1 1 1 1 DESCRIPTION M4X30 TMP PRF TH BLK M4X40 MSCR TH BLK M4X20 MSCR PAN W/FS PAS M6X30 BLT W/S BLK M6X16 BLT W/S BLK M6 WSHR FORM A FLT BLK M4X8 MSCR PAN W/FS PAS M4X8 TMP PRF TH CRM WIRE HARN TOWER EXT 2 WIRE HARN START EXT 2 WIRE HARN EXT 2 WIRE HARN EARTH 2200mm M4/M4 K WIRE HARN EARTH 400mm M4/M4 K COMPONENT REFERENCE (12)-8 (14)-4 (3)-4, (18)-5 (25)-8, (26, 27)-4 (24)-8 (24)-8 EARTHS-2 (32)-4 LH GUN HOLDER TO AC BRKT LH GUN HOLDER TO RH GUN HOLDER 91 8. 9. HDT-1150UK ASSY FENCE L Item 1 2 3 4 101 201 202 203 Component Part HOD-1351 HDT-1151UK HOD-0004UK HDT-1152UK 601-6076-OBUK 000-T00412-0B 068-441616-0B 050-C00400-3B Qty. 1 1 2 1 1 8 8 8 Description Component Reference PIPE L GUARD PLATE L PLATE HOLDER PLATE GUARD BASE LEG ADJUSTER 32MM BLACK M4X12 MSCR TH BLK (2)-6, (3)-2 M4 WSHR 16OD FLT BLK (2)-6, (3)-2 M4 NUT DOME TYPE 3 BLK (2)-6, (3)-3 92 8. 10. HDT-1160UK ASSY FENCE R Item 1 2 3 4 101 201 202 203 Component Part HOD-1361 HDT-1161UK HOD-0004UK HDT-1162UK 601-6076-OBUK 000-T00412-0B 068-441616-0B 050-C00400-3B Qty. 1 1 2 1 1 8 8 8 Description Component Reference PIPE R GUARD PLATE R PLATE HOLDER PLATE GUARD BASE LEG ADJUSTER 32MM BLACK M4X12 MSCR TH BLK (2)-6, (3)-2 M4 WSHR 16OD FLT BLK (2)-6, (3)-2 M4 NUT DOME TYPE 3 BLK (2)-6, (3)-2 93 8. 11. [. . . ]