User manual SEGA GHOST SQUAD UR

[. . . ] Be sure to keep this manual nearby the product or elsewhere convenient for referring to it when necessary. Herein, explanations which require special attention are enclosed with dual lines. Depending on the potentially hazardous degrees, the terms of WARNING, CAUTION, etc. Be sure to understand the contents of the displays before reading the text. [. . . ] 1 a SWITCH UNIT SOUND VOLUME SWITCH: (SOUND VOLUME) (SERVICE) (TEST) Adjusts sound volume for all of the machines' Speakers. For the handling of the test button, refer to the following pages. SERVICE BUTTON: TEST BUTTON: COIN METER Open the Cashbox Door by using the key to have the Coin Meter appear underneath the Cashbox. COIN METER FIG. 1 b www. sauservice. com 64 9-2 SYSTEM TEST MODE STOP IMPORTANT! Any settings that are changed by users during TEST MODE are saved upon exiting TEST MODE with the EXIT command in the SYSTEM MENU. If the unit is powered off prior to exiting, changes to settings will not take effect. You may not enter GAME TEST MODE while the unit is reading from or checking the GD-ROM. If error messages are displayed when exiting TEST MODE, you should power the unit off and on again. In the manual for this product, "Media Board" and "DIMM" are one and the same. If settings other than those specified are used, inappropriate operations or malfunction may occur. A. SYSTEM TEST MENU MODE System Test Mode can be used to check that the main circuit operations are correct, adjust Monitor color, and perform coin/credit settings. SOUND TEST - OUTPUT TYPE: STEREO COIN ASSIGNMENTS - COIN CHUTE TYPE: COMMON - SERVICE TYPE: COMMON Press the TEST Button after powering on the unit to display the following SYSTEM MENU. SYSTEM MENU MEDIA BOARD TEST SYSTEM INFORMATION JVS TEST SOUND TEST C. R. T. TEST COIN ASSIGNMENTS CLOCK SETTING NETWORK SETTING(CORE) NETWORK SETTING(MEDIA) ENTER GAME TEST [*******************] EXIT SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON Press the SERVICE Button to move the cursor to the desired test item. Move the cursor to EXIT and press the TEST Button to return to the SYSTEM MENU screen. www. sauservice. com 68 INPUT TEST Screen JVS TEST INPUT TEST NODE 1/1 SYSTEM 00 PLAYER 1 0000 PLAYER 2 0000 COIN 1 0000 COIN 2 0000 ANALOG 1 0000 ANALOG 2 0000 ANALOG 3 0000 ANALOG 4 0000 ANALOG 5 0000 ANALOG 6 0000 ANALOG 7 0000 ANALOG 8 0000 PRESS TEST AND SERVICE BUTTON TO EXIT (A) (A) (A) (B) (B) (C) (C) (C) (C) (C) (C) (C) (C) On-screen values change according to the input from switches and the volume. (A) (B) (C) SYSTEM, PLAYER Values change with input from control panel/other switches. ANALOG Displays analog values from "0000" to "FFFF". Press the SERVICE and TEST Buttons simultaneously to return to the JVS TEST main screen. 69 www. sauservice. com E. SOUND TEST Use SOUND TEST to test sound output and to select the stereo/mono/surround setting. SOUND TEST OUTPUT TYPE RIGHT SPEAKER LEFT SPEAKER EXIT STEREO OFF OFF (A) (B) (B) SELECT WITH SERVICE BUTTON AND PRESS TEST BUTTON Use the SERVICE Button to move the cursor to the desired test item. (A) OUTPUT TYPE(STEREO, MONO, SURROUND) Select the sound output from the I/O PANEL audio output interface setting among STEREO, MONO and SURROUND. RIGHT/LEFT SPEAKER(ON, OFF) When set to "ON", the test sends a beep to each audio output interface. Only the word "SPEAKER" is displayed when the OUTPUT TYPE is set to "MONO", and when set to "ON", the test sends the same beep to both the left/right audio output interfaces. To test surround output, it is necessary to use a separate Audio Amp, and receive signal from a terminal not in use at the time of shipping. Note: Not available with this product. (B) Move the cursor to EXIT and press the TEST Button to return to the SYSTEM MENU screen. www. sauservice. com 70 F. COLOUR CHECK Screen Monitor COLOUR CHECK screen is displayed initially. Each of the colours (red, green and blue) is darkest at the far left and gets progressively lighter (32 steps) towards the right. [. . . ] 601-0460 600-7009-1000 600-7141-100 CTF-60021 CTF-60022 CTF-60023 CTF-60024 CTF-60030 DESCRIPTION PLASTIC TIE BELT 100 M/M ASSY RGB CA D-SUB 15P 1000MM CABLE JVS TYPE A-B 100CM WH AUDIO EXT WH POWER EXT WH SENSOR LED EXT WH CARD RW & HOLDER WH START & SENSOR CONT NOTE www. sauservice. com 166 IC RW UNIT (CTF-1150) (D-1/2) 167 www. sauservice. com IC RW UNIT (CTF-1150) ITEM NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 101 102 103 104 105 106 107 108 201 202 203 204 205 206 207 301 302 PART NO. CTF-1151 CTF-1152 TBA-1662 TBA-1663 CFB-1664 CFB-1665 CFB-1666 TBA-1667 TBA-1668 TBA-1669 125-5225 839-1204-02 CTF-1153-01 610-0680 370-5161 601-11132 838-14463 280-5247 280-5248-7. 5 280-5009-01 280-5275-SR10 FAS-120001 000-P00410-W 060-F00400 000-P00308-W FAS-120017 065-E00300 000-P00320-W CTF-60028 CTF-60029 DESCRIPTION RW BASE CUSHION SPONGE RW RW GUIDE LOWER RW GUIDE UPPER ROLLER SOL BASE SENSOR BRKT LOCK ARM SHAFT SHAFT GUIDE TOR SPRING LOCK ARM SERIAL I/F BD CTF STICKER IC CARD ENG SOLENOID UNIT PHOTO INTERRUPTER GP1A71A IC CARD READER HW210 (TAMURA) LED BAR GD GREEN ONE TOUCH BUSHING ONE TOUCH COLLOR M3 L=7. 5 CORD CLAMP 21 CORD CLAMP SR10 TAP SCR #2 TH BLK 4X10 M SCR PH W/FS M4X10 FLT WSHR M4 M SCR PH W/FS M3X8 TAP SCR #2 TH 3X6 E RING 3MM M SCR PH W/FS M3X20 WH CARD RW 1 WH CARD RW 2 <OTHERS> NOTE (D-2/2) www. sauservice. com 168 ASSY SPEAKER PIPE (CTF-1200) Attach 101 so that the speakers are on the outside and the bass reflex ducts are on the inside. ITEM NO. CTF-1201 130-5228-01 280-5275-SR10 000-P00512-WB 012-P00512-0B 060-F00500-0B CTF-60025 DESCRIPTION JOINT PIPE REAR SPEAKER BOX 40OHM 40W CORD CLAMP SR10 M SCR PH W/FS BLK M5X12 TAP SCR #2 PH BLK 5X12 FLT WSHR BLK M5 WH SPEAKER EXT NOTE 169 www. sauservice. com ASSY CONTROLLER HOLDER (CTF-1300) Fastening Torque: 201 : 1. 4N·m(14kgf·cm) ITEM NO. [. . . ]