User manual SEGA FORD RACING TWIN

[. . . ] 420-FRSM-02UK REV 2 TWIN DRIVING CABINET SERVICE MANUAL · · Before using this product, read this MANUAL carefully to understand the contents stated herein. After reading this MANUAL, be sure to keep it available nearby the product or somewhere convenient in order to be able to refer to it whenever necessary. Manufactured in the UK by Amusements Europe Limited BEFORE USING THIS PRODUCT To ensure the safe usage of the product, be sure to read the following before using the product. The following instructions are intended for the use of QUALIFIED SERVICE PERSONNEL ONLY. After carefully reading and sufficiently understanding the instructions should any activity be carried out on the product. [. . . ] Check that each setting is set to the factory setting as per the time of shipment. In the CRT TEST check the adjustment of the picture and adjust if necessary. PERIODIC SERVICING Periodically perform the following tests: 1. In the SOUND TEST perform a sound check. MONITOR In the monitor check screen, check to see if the MONITOR adjustments are made correctly. Check such data as game play time and histogram and adjust difficulty levels if necessary. DATA CHECK 25 10. 1. VTS BOARD ­ SWITCHES AND COIN COUNTER · Never touch places other than those specified. Touching parts in places not specified may cause electric shock or a short circuit hazard. · Adjust to the optimum sound volume taking in consideration the environmental requirements of the installation location. VTS BOARD Open the top coin tower door and the VTS BOARD is located on the back panel. The function of each control is as follows: TEST BUTTON: Enables the SERVICE ENGINEER to enter the TEST MODE. Registers the count of coins inserted through the coin mechanism in 10p or 10 cent units. Adjusts the level of sound emitted from the front speakers. SERVICE BUTTON: DIP SWITCHES: STATUS LED: CREDIT BUTTON: COIN COUNTER: VOLUME CONTROL: 26 10. 2. TEST MODE · When changes are made in the TEST MODES, be sure to EXIT from the TEST MODES to return to GAME MODE. If power is turned OFF in TEST MODE, the new setting will not take effect. The Test Menu allows the functioning of each part of the cabinet to be checked, the monitor to be adjusted and the coins and various related game setting to be changed. o o o Press the test button to enable the TEST MODE to be displayed on screen. Press the SERVICE BUTTON to move the pointer on-screen to the desired function. Once the desired function has been established, press the TEST BUTTON to enter that particular test. SYSTEM INFORMATION UGCI TEST INPUT TEST CALIBRATE TEST OUTPUT TEST COIN TEST SOUND TEST CRT TEST DRIVE BOARD TEST BOOKKEEPING CLOCK SETTING NETWORK TEST GAME TEST EXIT Displays general information on installed software and hardware. Leaves System Test and returns to game mode. The operator uses the SERVICE button to select the desired test routines and presses the TEST button to activate choice. 27 10. 3. SYSTEM INFORMATION This test displays general system information regarding the hardware configuration and installed software. SYSTEM ID DISK IMAGE LAUNCHER VERSION GAME SHELL VERSION GAME NAME GAME VERSION UGCI VERSION IBUTTON EXIT A unique 64 bit ID code to identify the system Version number for master disk image Version number for System Launcher Version number for Game Shell Name of the installed game Version number of installed game Hardware version of installed UGCI board Type of iButton installed (Game Name or SYSTEM). If no iButton is installed, then a NOT FOUND message is shown Return to SYSTEM MENU The user cannot modify any of the parameters in this test. UGCI TEST This test is used to test the network link between the computer and the UGCI board. COIN 1 COUNT COIN 2 COUNT VERSION UGCI STATUS EXIT Value of UGCI NVR coin count 1 Value of UGCI NVR coin count 2 Version number of UGCI board OK is the system can communicate with the UGCI board, otherwise a NOT CONNECTED message is shown. Return to SYSTEM MENU The user cannot modify any of the parameters in this test. INPUT TEST This test is used to test and calibrate the peripherals connected to the UGCI interface. STEERING ACCELERATOR BRAKE GEAR SHIFT START CHANGE VIEW SERVICE TEST EXIT 00H = Full Left lock, 80H = Centre, FFH = Full right lock 00H = pedal fully up, FFH = pedal fully down 00H = pedal fully up, FFH = pedal fully down UP = stick up, N = stick central, DOWN = stick down On = pressed, OFF = not pressed On = pressed, OFF = not pressed On = pressed, OFF = not pressed On = pressed, OFF = not pressed Exit to System Menu Please refer to the CALIBRATION TEST for calibrating the hand and foot controllers. As this test will check for functionality of both the TEST and SERVICE buttons, in order to exit this test, BOTH buttons must be pressed simultaneously. 30 10. 6. CALIBRATION TEST This test is used to calibrate the analogue system input devices, i. e. the steering wheel, throttle pedal and brake pedal. STEERING LEFT VAL STEERING LEFT VAL BRAKE DOWN VAL BRAKE UP VAL THROTTLE DOWN VAL THROTTLE UP VAL CALIBRATE STEERING The current maximum left position of the steering wheel The current maximum right position of the steering wheel The current maximum down position of the brake pedal The current maximum up position of the brake pedal The current maximum down position of the throttle pedal The current maximum up position of the throttle pedal Starts the steering calibration routine. [. . . ] ASSY POP ­ FR-0270UK SEQ 1 2 3 4 5 PT NUMBER FR-2071UK FR-0272UK FR-0273UK FR-0274UK FR-0275UK DESCRIPTION POP PANEL FR BRKT SUPP POP LOWER BRKT SUPP STRUT L BRKT SUPP STRUT R BRKT CROSS BRACE POP QTY 1 1 1 1 1 91 25. 8. ASSY FAN UNIT DC ­ HDT-1530UK SEQ 1 101 102 301 PT NUMBER 105-5340-01 EC814500 FN1012 HDF-60004UK DESCRIPTION FAN BKT LONG 12V DC FAN 120MM KD1212PMS3-6A FAN GUARD METAL 120MM FG-12 WIRE HARNESS FAN LINK (NOT SHOWN) QTY 2 1 1 1 92 25. 9. ASSY SEAT TWIN 1P ­ FR-5000UK SEQ 1 2 PT NUMBER FR-5500UK FR-5600UK DESCRIPTION ASSY SEAT CABI ASSY SEAT UNIT QTY 1 1 25. 10. ASSY SEAT CABI ­ FR-5500UK SEQ 1 2 3 7 PT NUMBER FR-5501UK MA1019 FR-5505UK 601-5699UK DESCRIPTION WOODEN SEAT CABI CASTER 75 JOINT PLATE LEG ADJUSTER M16X100 1L/NUT QTY 1 3 2 4 93 25. 11. [. . . ]