User manual SEGA FASTER THAN SPEED

[. . . ] Align the holes of legs to the holes on the bottom of the table, and then secure it with big flathead screw (5mm x 35mm) and flat washer (8mm x 16mm) leg levelers x 4 roundhead screw (8mm x 25mm) flat washer (8mm x 16mm) Step 2 :Once the legs are tightly screwed on to the table base, flip and position the table by 90 degree angle ; this action would require at least 3~4 people, then flip it again in same manner to conclude with the upright position as shown on the diagram: FINISHED PICTURE 4. Assembling Instruction Step 3 :Attach the center guard on one side with big flathead screw (5mm x 15mm). As to the other side, insert the center guard into the iron plate first before screw it tightly . Insert the center guard into the other side first , and then screw to the iron plate . Screw the iron plate on one side with big flathead screw (5mm x 15mm) ( Finished as shown ) FINISHED PICTURE 5. Assembling Instruction Step 4 :Attach the overhead bar bracket with big flathead screw (5mm x 15mm). Note: DO NOT screw it too tightly, only screw-in by 1/3 as overhead bars need to be placed in first, so do not tightly screw on both sides. ( Finished as shown ) Use ( 4 ) of the big flathead screw (5 mm x 1 5 mm ) to screw - in the overhead bar bracket , but not tightly . FINISHED PICTURE 6. Step 5 :Connect the Scoreboard and the overhead bar. [. . . ] Place the sonic sign fastener on the centre of the overhead bar then tightly screw it with ( 3 ) big flathead screw (5 mm x 15 mm ). Then use ( 4 ) big flathead screw (4 mm x 12 mm ) to connect the Scoreboard with the sonic sign fastener. 3 x big flathead screw (5mm x 15mm) Assemble Instruction 4 x big flathead screw (4mm x 12mm) Step 6 :Screw the sonic sign fastener on the scoreboard . Use ( 8 ) big flathead screw (4 mm x 12 mm ) to screw the sonic sign fastener tightly onto the scoreboard . 8 x big flathead screw (4mm x 12mm) FINISHED PICTURE 7. Assemble Instruction Step 7 :Connect the Scoreboard with the overhead bar then insert the set into the overhead bar bracket . Note : the connector plugs need to be inserted into the overhead bar bracket first. Please do not bend or press the connector wires. Insert the Scoreboard set (including the overhead bar) into the overhead bar bracket , NOTE : the part with the connector plugs should face inside. Connector plug end Connector plug end need to pass through the overhead bar bracket first set Insert trough Step 8 :Plug-in all the plugs on the connector plug end in accordance to its colors. NOTE: plug-in tightly. All plugs are separated by colors 8. Assemble Instruction Step 9 :Use the open - cut side of the overhead bar plastic cover, and then insert it into the overhead bar protection cover. If there is no light or the light stays on continuously, then it means the goal sensor is broken. PC Board Lights If lights on Pc Board are on for coin mechanism and/or ticket dispenser , there is an error for the corresponding light(s). II. Ticket Dispenser Flashing light on ticket dispenser means out of tickets. Restart table if light does not appear with new tickets inserted. III. Coin Mechanism/Acceptor Make sure to replace the sample plastic coin with the desired number of coins. Puck Release If puck is grtting stuck inside of the release door , the following need to be check for possible errors : 1) Check for debris , shavings , paper and other emains lodged inside the return unit. 3) Wire connector to release solenoid has become unplugged/ damaged/stuck/broken. [. . . ] 3) Wire connector to release solenoid has become unplugged/ damaged/stuck/broken. Push Start Sound If you hear "PUSH START" , the following need to be checked and corrected. 2) Both coin acceptors and ticket dispensers are properly plugged in and connected. [. . . ]