User manual SEGA DERBY OWNERS CLUB WORLD EDITION

[. . . ] www. seuservice. com 1st PRINTING JUNE 02 OWNER'S MANUAL SEGA ENTERPRISES, INC. USA MANUAL NO. 420-6679 VISIT OUR WEBSITE! BEFORE USING THE PRODUCT, BE SURE TO READ THE FOLLOWING: To maintain the safety: To ensure the safe usage of the product, be sure to read the following before using the product. The following instructions are intended for the users, operators and the personnel in charge of the operation of the product. After carefully reading and sufficiently understanding the warning displays and cautions, handle the product appropriately. [. . . ] Damaging the power cords can cause an electric shock and/or short circuit. When lifting the cabinet, be sure to hold the catch portions or bottom part. Lifting the cabinet by holding other portions can damage parts and installation portions due to the empty weight of the cabinet, and cause personal injury. WARNING! CAUTION! Do not use a forklift to move this product. This could cause breakage of components, and the pieces could cause injury. This could cause breakage of components, and the pieces could cause injury. This could cause breakage, and workers could suffer injury from the pieces. STOP IMPORTANT! When transporting the product in places with steps, disassemble into each unit before transporting. Inclining the product in an as is assembled condition or placing the cabinet in places with steps can damage the unit's joining portions. To protect surface, do not directly apply a rope to the surfaces of product. Use protective materials to the places the rope is applied to. On level surfaces, move the machine by causing the casters to make contact with the surface. FIG. 7 a Casters of the main projection unit www. seuservice. com 48 On level surfaces, move the machine by causing the casters to make contact with the surface. FIG. 7 b Casters of the satellite Do not push on the plastic components such as the projectors or screen. FIG. Do not move by pulling on plastic components. Do not push on the armrests. To move, use the handles. FIG. CARD READER/WRITER STOP IMPORTANT! The card reader/writer features dip switches in three locations. Changes to these settings could cause malfunctioning. DIP SW 1 represents the communication setting. OFF DIP SW 3 DIP SW 2 DIP SW 1 PHOTO 8 DIP SW 2 and 3 are for minute adjustments prior to final shipping. Changes can result in malfunctions such as a slight divergence in the printing position. www. seuservice. com 50 8 - 1 SETTING THE CARDS STOP IMPORTANT! Please be sure to use the proprietary cards for this product. Be sure to set the cards in accordance with the specified procedure, direction, and number. Do not set more than 100 cards, as this could cause problems such as jamming. Do not mix with cards that have been creased, bent, or previously used. The card reader/writer, in which the cards are to be set, is to the left of the monitor screen, as seen when facing the satellite. Cards can be set regardless of whether the power is switched to ON or OFF. Release. RW COVER 1 Release and open the RW cover to reveal the card reader/writer. The card reader/writer contains a card dispenser. CARD READER/WRITER DISPENSER PHOTO 8. 1 a 2 Remove the dispenser by pulling straight up from the card reader/ writer. PHOTO 8. [. . . ] 4 Disconnect all other connectors from the shield case to other devices. 5 Remove the 2 screws securing the base to allow removal of the shield case mounted on its base. Be careful not to damage the wiring during removal. 6 Remove the 4 screws to remove the shield case from the base. 95 www. seuservice. com Disconnect all the connectors. Disconnect the communication cables. SCREW (2) M4 X 30, w/flat & spring washers, flat washer used. MAINTENANCE DOOR R Release. TRUSS SCREW(black)(2) M4×30 Disconnect all the connectors. SCREW (4) M4×12, w/flat and spring washers Disconnect all the connectors. SHIELD CASE FIG. [. . . ]