User manual SEGA DAYTONA2

[. . . ] ACCELERATOR & BRAKE 10ADJUSTMENT AND REPLACEMENT OF VOLUME 1 10GREASING 2 11. 4-SPEED SHIFTER 11REMOVING THE SHIFTER 1 11REPLACING THE SWITCH 2 http://www. sauservice. com/manuals/Daytona%20Folder/DDhtml/DD00. html 7/12/2005 Daytona USA Deluxe Owner's Manual Page 2 of 2 113 114 12. 171 172 173 18. GREASING REPLACEMENT OF RUBBER STOPPERS COIN SELECTOR PROJECTOR CLEANING THE SCREEN HITACHI PROJECTOR MITSUBISHI PROJECTOR REPLACING THE FLUORESCENT LAMP PERIODIC CHECK TROUBLESHOOTING GAME BOARD REMOVING THE BOARD COMPOSITION OF GAME BOARD INPUT AND OUTPUT RELATIONS DESIGN RELATED PARTS 38 38 39 40~43 40 41 42 44 44 45 46~47 46 47 47 48~49 50~96 97 98~99 19. WIRING DIAGRAM http://www. sauservice. com/manuals/Daytona%20Folder/DDhtml/DD00. html 7/12/2005 Introduction of the Owner's Manual Page 1 of 2 [Table of Contents][Next Page] SPECIFICATIONS Installation space Height Weight Power, maximum current 1, 140 mm (W) x 2, 800 mm (D) (44. 9 in. [. . . ] To check CHUTE 1 & CHUTE 2 coin switches, open the COIN CHUTE DOOR and insert a coin (s) from the coin entry. To return back to the MENU mode, simultaneously press VR1 & VR2, or press the TEST SW. FIG. is as follows: Under 2DH <-- 7D~83H --> Over D3H left (Centering position) right ACCEL: Under 30H ---> Over COH BRAKE: Under 30H ---> Over D2H (the pedal released) (the pedal stepped) HANDLE: http://www. sauservice. com/manuals/Daytona%20Folder/DDhtml/DD26. html 7/12/2005 Output Test Page 1 of 2 [Table of Contents] [Previous Page] [Next Page] 8-7 OUTPUT TEST Choose OUTPUT TEST to cause the following topmost screen to appear. In this test, periodically adjust the projector and check the status of each lamp. Press the SERVICE SW or VR4 (green)/VR1 (red) and bring the arrow (>>) to the desired test item. Press the TEST SW or START SW to cause the test mode screen below to appear. To return back to the menu mode, bring the arrow to EXIT and press the TEST SW or START SW (FIG. Adjust the projector (monitor) to make sure that the crosshatch lines do not go beyond the screen size and crosshatch distortion does not occur. Press the START SW to return to the above OUTPUT TEST menu screen. Choose CRT COLOR to cause the screen shown at the left to appear. e. , red, green, blue, and white) is darkest at the leftmost end and brightest at the rightmost end. http://www. sauservice. com/manuals/Daytona%20Folder/DDhtml/DD27. html 7/12/2005 Output Test Page 2 of 2 Choose LAMP to cause the screen shown at the left to appear. Press the START SW to return to the above OUTPUT TEST menu screen. http://www. sauservice. com/manuals/Daytona%20Folder/DDhtml/DD27. html 7/12/2005 Drive BD Test Page 1 of 1 [Table of Contents] [Previous Page] [Next Page] 8-8 DRIVE BD TEST Choosing DRIVE BD TEST allows the reaction mechanism of the steering wheel to be checked. 8. 12 BACKUP RAM http://www. sauservice. com/manuals/Daytona%20Folder/DDhtml/DD32. html 7/12/2005 Handle's V. R. Page 1 of 2 [Table of Contents] [Previous Page] [Next Page] 9. CONTROL PANEL (HANDLE MECHA) In the TEST mode, if the steering wheel V. value variations are not within the allowable range, an adjustment of the V. Also, apply grease to the steering wheel mechanism's shaft and sliding portions once every 3 months. When carrying out the above work, take off the 4 truss screws and remove the front cabi's Front Lid Upper. 9-1 REPLACING AND ADJUSTING THE HANDLE's (STEERING WHEEL's) V. R. FIG. is as follows: When the steering wheel is Left Centering position Right turned to or positioned at: V. to be replaced, take out the 2 screws which secure the VR BRACKET, and remove the V. value variations in the test mode. http://www. sauservice. com/manuals/Daytona%20Folder/DDhtml/DD33. html 7/12/2005 Handle's V. R. Page 2 of 2 http://www. sauservice. com/manuals/Daytona%20Folder/DDhtml/DD33. html 7/12/2005 Greasing Page 1 of 1 [Table of Contents] [Previous Page] [Next Page] Method of V. value is not appropriate when the steering wheel is at the centering position, loosen the 2 screws which secure the V. value variations by turning the handle. 9-2 GREASING Once every 3 months, grease the gears, bearings, springs, and cam & arm's sliding portions. http://www. sauservice. com/manuals/Daytona%20Folder/DDhtml/DD34. html 7/12/2005 Volume Page 1 of 2 [Table of Contents] [Previous Page] [Next Page] 10. [. . . ] activated. http://www. sauservice. com/manuals/Daytona%20Folder/DDhtml/DD45. html 7/12/2005 Troubleshooting Page 2 of 2 strength is insufficient. Fluorescent lamp doesn't light up. POWER ON CHECK not performed correctly. 14). http://www. sauservice. com/manuals/Daytona%20Folder/DDhtml/DD45. html 7/12/2005 Removing the Game Board Page 1 of 2 [Table of Contents] [Previous Page] [Next Page] 17. GAME BOARD 17-1 REMOVING THE BOARD To replace the IC BD (such as Game BD, Drive BD, etc. ), or to change DIP SW settings, take out the IC BD by using the following procedure: 1. To remove the BUMPER, take off the 2 screws, one each on both sides and unfasten the 2 snap fasteners, one each on both sides from the inside of the rear cabi. [. . . ]