User manual SEGA DAYTONA SPECIAL

[. . . ] ACCEL & BRAKE (S) 9-1 ADJUSTMENT AND REPLACEMENT OF VOLUME 9-2 GREASING 9-3 HAND BRAKE 10. MAINTENANCE OF MECHANISM UNIT 10-1 ADJUSTMENT AND REPLACEMENT OF VOLUME 10-2 GREASING 10-3 REPLACEMENT OF SAFETY RUBBER 1 2~3 4~5 6 7~8 9~15 16 17~21 22~32 23 24 24 25 26 26 27 27 28 29~31 32 32 33~37 33~34 35 36 37 38~40 38~39 39~40 40 41~46 41~42 43~44 45~46 http://www. sauservice. com/manuals/Daytona2dlx_html/day2dlxtoc. html 7/12/2005 Table Of Contents DAYTONA 2 DLX Page 2 of 2 11. PROJECTOR 12-1 CLEANING THE SCREEN 12-2 MITSUBISHI MONITOR 12-3 TOSHIBA MONITOR 13. REPLACEMENT OF FLUORESCENT LAMP AND LAMPS 13-1 REPLACEMENT OF FLUORESCENT LAMP 14. [. . . ] The Foot Controller is locked with the Slide Lock in the ON status, and Unlocked to become free with the Slide Lock in the OFF status. Press the test Button to return to the MENU MODE. 7 - 7 SOUND TEST This enables sound used in the game to be checked. Sound related memory and each speaker are checked. http://www. sauservice. com/manuals/Daytona2dlx_html/13day2dlx. html 7/12/2005 Test Mode Page 3 of 3 Press the SERVICE BUTTON to bring the arrow to the desired sound item to be tested. Each time the SERVICE BUTTON is pressed, the numeral displayed on the screen counts up and sound is admitted. Bring the ">" to EXIT and press the TEST BUTTON to return to the MENU MODE. 7 - 8 C. R. T. TEST to cause the MONITOR to display the screen shown left, allowing MONITOR adjustment status to be checked. Periodically check the MONITOR adjustment status on this screen. The screen (1/2) enables color adjustment check to be performed. The color bar of each of the 4 colors, i. e. , red, green, blue, and white, is the darkest at the extreme left and becomes brighter towards the extreme right. Press the TEST BUTTON to shift to the next screen (2/2). The screen (2/2) allows screen size and distortion to be tested. Check if the CROSSHATCH FRAME LINE goes out of the screen and if the crosshatch lines are distorted. Press the TEST BUTTON to return to the MENU mode. 6. 2) http://www. sauservice. com/manuals/Daytona2dlx_html/13day2dlx. html 7/12/2005 Game Assignments Page 1 of 2 [Previous page][Next page][Table of Contents] 7 - 9 GAME ASSIGNMENTS Selecting the GAME ASSIGNMENTS in the MENU mode causes the present game settings to be displayed and also the game settings changes (game difficulty, etc. ) can be made. Each item displays the following content. Setting changes cannot be stored unless the TEST BUTTON is pressed while the arrow is on EXIT. SETTING CHANGE PROCEDURE (1) Press the SERVICE BUTTON to move the ">" to the desired item. (2) Choose the desired setting change item by using the TEST BUTTON. (3) To return to the MENU mode, move the arrow to EXIT and press the TEST BUTTON. The Following FIGURES/TABLES show the factory recommended settings. ADVERTISE SOUND Determines whether ADVERTISE SOUND is to be emitted or not by the setting to ON when emitting it and to OFF when not emitting it. http://www. sauservice. com/manuals/Daytona2dlx_html/16day2dlx. html 7/12/2005 Game Assignments Page 2 of 2 GAME DIFFICULTY Sets the Game Difficulty in 8 categories from 1 to 8. The greater the number is, the higher the difficulty level becomes. http://www. sauservice. com/manuals/Daytona2dlx_html/16day2dlx. html 7/12/2005 Coin Assignments Page 1 of 2 [Previous page][Next page][Table of Contents] The "COIN ASSIGNMENTS" mode permits you to set the start number of credits, as well as the basic numbers of coins and credits. This mode expresses "how many coins correspond to how many credits. " Setting changes cannot be stored unless the TEST BUTTON is pressed while the arrow is on EXIT. 7 - 10 COIN ASSIGNMENTS SETTING CHANGE PROCEDURE: (1) Press the SERVICE BUTTON to move the arrow to the desired item. Performing work by non-technical personnel can cause shock hazard. If appropriate value of each V. R. Since work is performed inside the energized cabinet, be very careful so as not to touch undesignated portions. Touching places not specified can cause electric shock or short circuit accident. (1) Take out the 2 truss screws and remove the Front Cover fromthe Accel & Brake Unit. (2) Loosen the screw which secures the Potentiobase, and adjust the Volume value by moving the Base. http://www. sauservice. com/manuals/Daytona2dlx_html/23day2dlx. html 7/12/2005 Greasing to Gear portion Page 2 of 4 (3) Secure the Potentiobase. (4) Perform Volume setting in the Volume setting mode. In order to prevent an electric shock and short circuit accident, be sure to turn power off before performing work by touching the interior parts of the product. Touching places not specified can cause an electric shock or short circuit accident. REPLACING THE VOLUME (1) Turn power off. (2) Disconnect the Connector. (3) Remove the Volume Bracket by taking out the 2 screws which secure the Volume Bracket. (4) Remove the Volume Gear and Volume Bracket to replace the Volume. Adjust gear mesh and ensure that Volume value display is within the range of 80+/-2H when the handle is in the centering position. http://www. sauservice. com/manuals/Daytona2dlx_html/23day2dlx. html 7/12/2005 Greasing to Gear portion Page 3 of 4 9 - 2 GREASING Be sure to use designated grease. Greasing to undesignated places can cause malfunctioning and the qualitative deterioration of parts. Once every 3 months, apply greasing to the SWING Volume gear mesh portion, Swing Frame supportive bearings, and Motor gear mesh portion. 090-0066). 8 - 2 GREASING 9 - 3 HAND BRAKE In order to prevent electric shock and short circuit, be sure to turn power off before performing work by touching the interior parts of the product. Touching places other than those specified can cause an electric shock or short circuit accident. Once every 3 months, apply greaing to the Spring inside the hand Brake. 090-0066) http://www. sauservice. com/manuals/Daytona2dlx_html/23day2dlx. html 7/12/2005 Greasing to Gear portion Page 4 of 4 GREASING (1) Turn Power off. (2) Take out the 9 screws and remove Side Cover B. (3) Apply greasing to the Spring portion. REPLACING THE HAND BRAKE SWITCH (1) Turn power off. (2) Replace the Microswitch inside Side Cover B by taking out the 2 screws. http://www. sauservice. com/manuals/Daytona2dlx_html/23day2dlx. html 7/12/2005 Mecha Unit Page 1 of 4 [Previous page][Next page][Table of Contents] 10. MAINTENANCE OF MECHANISM UNIT 10 - 1 ADJUSTMENT AND REPLACEMENT OF VOLUME Be careful so as not to damage wirings. touching places other than thos specified can cause electric shock or short circuit accident. [. . . ] Be very careful when replacing the Fluorescent Lamp. To perform work safely and securely, be sure to prepare a step which is in a secure and stable condition. Not using a step or using an unstable step can cause a violent falling down accidents. 13 - 1 REPLACEMENT OF FLUORESCENT LAMP Take off the 3 screws which secure the Holder on the upper part of Billboard. Take out the billboard from the cabinet and replace the fluorescent lamp (20W) http://www. sauservice. com/manuals/Daytona2dlx_html/29day2dlx. html 7/12/2005 Replacement of Lamps Page 2 of 2 http://www. sauservice. com/manuals/Daytona2dlx_html/29day2dlx. html 7/12/2005 Periodic Inspection Table Page 1 of 2 [Previous page][Next page][Table of Contents] 14 . PERIODIC INSPECTION TABLE The items listed below require periodic check and maintenance to retain the performance of this machine and ensure safe operation. Be sure to check once a year to see if Power Cords are damaged, the plug is securely inserted, dust is accumulated between the Socket Outlet and the Power Plug, etc. Using the product with dust as is accumulated can cause a fire or electrical shock. Periodically once a year, request the place of contact herein stated or the Distributor, etc. [. . . ]