User manual SEGA DAYTONA 2 USA DELUXE TYPE

[. . . ] Table Of Contents DAYTONA 2 DLX Page 1 of 2 DAYTONA 2 USA DELUXE TABLE OF CONTENTS INTRODUCTION TO THE OWNER'S MANUAL GENERAL PRECAUTIONS 1. EXPLANATION OF TEST AND DATA DISPLAY 7-1 SWITCH UNIT AND COIN METER 7-2 TEST MODE 7-3 MEMORY TEST 7-4 T. G. P. TEST 7-9 GAME ASSIGNMENTS 7-10 COIN ASSIGNMENTS 7-11 BOOKKEEPING 7-12 BACKUP DATA CLEAR 8. MAINTENANCE OF HANDLE AND SHIFT LEVER 8-1 ADJUSTMENT AND REPLACEMENT OF SWING VOLUME 8-2 GREASING 8-3 REMOVING SHIFT LEVER 8-4 SWITCH REPLACEMENT 9. [. . . ] The greater the number is, the higher the difficulty level becomes. http://www. sauservice. com/manuals/Daytona2dlx_html/16day2dlx. html 7/12/2005 Coin Assignments Page 1 of 2 [Previous page][Next page][Table of Contents] The "COIN ASSIGNMENTS" mode permits you to set the start number of credits, as well as the basic numbers of coins and credits. This mode expresses "how many coins correspond to how many credits. " Setting changes cannot be stored unless the TEST BUTTON is pressed while the arrow is on EXIT. 7 - 10 COIN ASSIGNMENTS SETTING CHANGE PROCEDURE: (1) Press the SERVICE BUTTON to move the arrow to the desired item. (3) To return to the MENU mode, move the arrow to EXIT and press the TEST BUTTON. COIN CHUTE TYPE: Sets the combination of the number of COIN CHUTEs and the number of players as applicable. In the case that the COIN CHUTE is changed, be sure the setting is made in a manner meeting the replaced coin chute. COMMON: Coins are accepted in common for both players. http://www. sauservice. com/manuals/Daytona2dlx_html/17day2dlx. html 7/12/2005 Coin Assignments Page 2 of 2 INDIVIDUAL: Each player uses a coin chute which accepts coins independently. CREDIT TO START: Number of credits required for starting game (1~5 credits are selected. ) CREDIT TO CONTINUE: Number of credits required for continuing game (1~5 credits are selected. ) COIN/CREDIT SETTING: Sets the CREDITS increase increment per coin insertion. There are 27 settings from #1 to #27, expressed in XX CREDIT as against XX COINS inserted. When the COIN CHUTE TYPE is set to INDIVIDUAL, there are some setting numbers not displayed as indicated in TABLE 7. 10b. MANUAL SETTING: This allows credit increase setting as against coin insertion to be further set in the manner finer than COIN/CREDIT SETTING (refer to TABLE 7. 10c). http://www. sauservice. com/manuals/Daytona2dlx_html/17day2dlx. html 7/12/2005 Bookkeeping/Backup Data Clear Page 1 of 2 [Previous page][Next page][Table of Contents] 7 - 12 BOOKKEEPING Choosing BOOKKEEPING in the MENU mode displays the data of operating status up to the present are shown on 2 pages. COIN CHUTE#*: Number of coins put in each Coin Chute. TOTAL COINS: Total number of activations of Coin Chutes. COIN CREDITS: Number of credits registered by inserting coins. SERVICE CREDITS: Credits registered by the SERVICE BUTTON. TOTAL CREDITS: Total number of credits (COIN CREDITS+SERVICE CREDITS). TOTAL TIME: The total energized time. http://www. sauservice. com/manuals/Daytona2dlx_html/21day2dlx. html 7/12/2005 Bookkeeping/Backup Data Clear Page 2 of 2 On page (2/2), each play frequency is displayed. When setting difficulty levels, the frequency can be referred to as a standard. When in the PAGE 2/2 mode, press the TEST BUTTON to return to the MENU mode. 7 - 13 BACKUP DATA CLEAR Clears the contents of BOOKKEEPING and high score player ranking entry. When clearing, bring the arrow to "YES" and when not clearing bring the arrow to "NO", by using the SERVICE BUTTON, and press the TEST BUTTON. Bring the arrow to "NO" and press the TEST BUTTON to cause the MENU MODE to return to the screen. Note that that contents of the GAME SETTING, COIN SETTING, and VOLUME SETTING are not affected by BACKUP DATA CLEAR operation. http://www. sauservice. com/manuals/Daytona2dlx_html/21day2dlx. html 7/12/2005 Mecha Unit/ Adjustment Page 1 of 5 [Previous page][Next page][Table of Contents] 8 . MAINTENANCE OF HANDLE AND SHIFT LEVER In order to prevent an electric shock and short circuit, be sure to turn power off before performing work by touching the interior parts of the product. Touching places not specified can cause an electric shock accident. In the test mode, if the handle V. R. in the following procedure. 8 - 1 ADJUSTMENT AND REPLACEMENT OF SWING VOLUME SETTING THE VOLUME (1) In the test mode, have the V. R. value displayed on the screen. (2) Remove the 11 screws from the right-hand side Panel Cover. (3) Loosen the 2 screws which secure the Volume Bracket, and you can move the Volume http://www. sauservice. com/manuals/Daytona2dlx_html/22day2dlx. html 7/12/2005 Mecha Unit/ Adjustment Page 2 of 5 Bracket. (4) Moving the Volume Bracket disengages the gear mesh. (5) Secure the handle to the centering position and adjust the gear mesh so that the position of Volume value is within the range 80+/-2H. (6) Fasten the 2 securing brackets. (7) Set the volume in the Volume Setting Mode. REPLACING THE VOLUME (1) Turn Power off. (2) Disconnect the Connector. (3) Remove the Volume bracket by taking out the 2 screws which secure the Volume Bracket. http://www. sauservice. com/manuals/Daytona2dlx_html/22day2dlx. html 7/12/2005 Mecha Unit/ Adjustment Page 3 of 5 (4) Remove the Volume Gear and Volume Bracket to replace the Volume. Adjust the gear mesh and ensure that Volume value display is within the range of 80+/-2H when the handle is in the centering position. 8 - 2 GREASING In order to prevent electric shock and short circuit, be sure to turn off power before performing work by touching the interior parts of the product. Greasing to undesignated places can cause malfunctioning and the qualitative deterioration of parts. Once in 3 months, apply greasing to Volume Gear Mesh Portion. 090-0066). 8 - 3 REMOVING THE SHIFT LEVER In order to prevent an electric shock and short circuit accident, be sure to http://www. sauservice. com/manuals/Daytona2dlx_html/22day2dlx. html 7/12/2005 Mecha Unit/ Adjustment Page 4 of 5 turn power off before performing work by touching the interior parts. Damaged wirings can cause an electric shock or short circuit accident. Touching places not specified can cause an electric shock or short circuit accident. If the Shift Lever operation is not satisfactory, remove the Shift Lever in the following procedure and replace the micro switch. (1) Take out the 6 truss screws and remove the Shift Cover. (2) Remove the 4 Hexagon Bolts which secure the Shift Lever. (3) Carefully lift the Shift Lever so as no to damage the Shift Lever's wiring connections, and disconnect the connectors. 8 - 4 SWITCH REPLACEMENT Each Micro switch is secured with 2 screws. After replacing the Switch, check to see if the switch is inputted as per Shift Lever operation in the Test Mode. http://www. sauservice. com/manuals/Daytona2dlx_html/22day2dlx. html 7/12/2005 Mecha Unit/ Adjustment Page 5 of 5 After replacing the Switch, check to see if the switch is inputted as per Shift Lever operation in the Test Mode. http://www. sauservice. com/manuals/Daytona2dlx_html/22day2dlx. html 7/12/2005 Greasing to Gear portion Page 1 of 4 [Previous page][Next page][Table of Contents] 9. Touching places not specified can cause an electric shock or short circuit accident. If Accel. [. . . ] where the product was purchased from, as regards the interior cleaning. Using the product with dust as is accumulated in the interior without cleaning can cause a fire or accident. Note that cleaning the interior parts can be performed on a pay-basis. ITEMS DESCRIPTION Cleaning Volume Check Check VR Check COIN SW COIN SELECTOR cleaning C. R. T. cleaning Check adjustments Setting check Cleaning Inspection and cleaning Cleaning PERIOD as required Weekly Monthly Monthly Trimonthly REFERENCE CONTROLLER 6 6 COIN SELECTOR 6 8 PROJECTOR Weekly Monthly Monthly Annually Annually As necessary 9 3, 6, 9 6 see above. [. . . ]