User manual SEGA AQUARACE VER.0.2

[. . . ] 0. 2 For your safe and correct use, read this manual carefully and understand it thoroughly before operation. Please keep this manual in a safe place at all times and refer to it for any future references. Make sure to pass this manual on to future owners of Mini Rider2 when the product is moved or sold. BEFORE USING THE PRODUCT, BE SURE TO READ THE FOLLWING: To maintain safety: To ensure the safe operation of this product, be sure to read the following before usage. The following instructions are intended for the users, operators and the personnel in charge of the operation of the product. [. . . ] Please install it conferring the following figure. < Fig 7-2a> It will be installed in SIDE FENCE SUPPORTER with four Hex Bolts (M6 x 20L). In installment, the SENSOR CABLE under the SENSOR must be in advance placed outside through the pipe. Please, be careful not to be confused with the direction of between the right and the left. The sensor attached with REFLECTOR should be in the left. < Fig 7-2b > 23 SIMULINE INC. . (3) SIDE FENCE SUPPORTER installation SIDE FENCE SUPPORTER can be installed at the side of BASE FRAME with four Hex Bolts (M6 x 20L). They must be installed at the both right and left sides of BASE FRAME. The upper side of REAR SIDE SUPPORTER and that of BASE FRAME should be fixed in a parallel way. At this time, the cables must be connected with the ones with the same tags so that REAR and RIGHT SENSOR CABLE may not be exchanged. Please remember that when you step on REAR SIDE SUPPORTOR in the state of REAR SIDE FENCE not installed, it can be damaged. < Fig 7-3 > 24 SIMULINE INC. . (4) REAR SIDE FENCE installation REAR SIDE FENCE can be installed with eight Hex Bolts (M8 x 20L). < Fig 7-4a > It can be fixed by FIX NUT after lifting two Adjusters at the maximum level. Rear Side Fences must be installed at the both right and left sides of BASE FRAME. < Fig 7-4b > 25 SIMULINE INC. . (5) REAR FENCE installation REAR FENCE will be installed in the tap hall at the backside of REAR SIDE FENCE with eight Hex Bolts (M8 x 20L). In case the level of the hall is not fit in, please rearrange the height of ADJUSTER in REAR SIDE FENCE. < Fig 7-5 > (6) SIDE STEP installation SIDE STEP in the side of BASE FRAME can be fixed with four Hex Bolts (M8 x 20L). They must be installed at the both right and left sides of BASE FRAME < Fig 7-6 > 26 SIMULINE INC. . (7) RIGHT FRONT FENCE installation This can be installed at the right front of BASE FRAME with four Hex Bolts (M8 x 20L). < Fig 7-7 > (8) COINCHUTE TOWER installation After you open SIDE DOOR of COINCHUTE TOWER, you must place the cable through a wiring hole. < Fig 7-8a > 27 SIMULINE INC. . The CONNECTOR of the main body and that of COINCHUTE TOWER will be connected at the lower end of SIDE DOOR. The EARTH CABLE of the main body must be thrusted toward COINCHUTE TOWER, hooked on a BOLT, and fixed by a M4 NUT. < Fig 7-8b > COINCHUTE TOWER will be installed at the left side of BASE FRAME with four Hex Bolts (M8 x 20L). < Fig 7-8c > You can shut SIDE DOOR. 28 SIMULINE INC. . (9) LEFT FRONT FENCE installation This can be installed at the left front of BASE FRAME with eight Hex Bolts (M8 x 20L). < Fig 7-9 > 29 SIMULINE INC. . (10) BILLBOARD Installation After you push up the Billboard over the Monitor, you can hang it on CATCH CLIP, and fix it with four Hex Bolts (M8 x 20L) conferring the following figure. < Fig 7-10a > After opening the COVER at the backside of Billboard, you can connect LED POWER CABLE. And then you can close the COVER. < Fig 7-10b > 30 SIMULINE INC. . (11) MSCU Installation At first, MSCU CABLE COVER assembled at MUSC must be disjointed < Fig 7-11a > After you connect it with two VIBROISOLATION Bolts, M10 x 25L in the front side of BASE FRAME, you can push MUSC in a hole. < Fig 7-11b > The Connectors which are outside of the front of the main body and backside of MSCU should be connected according to their shapes. After opening AC UNIT and SIDE COVER as in Fig 7-11c, Fig 7-11d, you can connect it with the front side of BASE FRAME by VIBRISOLATION BOLT, M10 x 25L and M10 NUT. EARTH CABLE can be connected as in Fig 7-11e. 31 SIMULINE INC. . < Fig 7-11c > < Fig 7-11d> < Fig 7-11e> You can fix again the disjointed MSCU CABLE COVER by using RACHET DRVIER. 32 SIMULINE INC. . < Fig 7-11f > Finally, you can install MSCU & BASE WIRE at the both right and left sides with HEX BOLT, M6 x 20L. < Fig 7-11g > 33 SIMULINE INC. . (12) Power Cable When connecting the cable for power, refer to [2. If the power source is not protected with a circuit breaker, accidents such as power leakage and fire can occur. Prepare a securely connected earth probe for the product and connect the product with earth line. If the product is not earthed properly, electric shock, damages to the product, and malfunction may occur. Do not expose the power cable or the earth cable out in a place such as a walkway. Cover the cables well with a cable molds or conceal the cables so they cannot be seen. If the cables are not secured properly, movements of the product may cause electric shock to customers or malfunction of the product. The power cable must be 10mm~14mm in diameter and 3 line cable(with 2 power lines and 1 earth line. ) Outer 8mm When connecting the power cable or earth cable to the Inner 4. 5mm product, use a type `O' terminal as shown here. The Power cable is not included. 34 SIMULINE INC. . After checking MAIN POWER SWITCH is OFF (0), please unpasten CAP NUT at CABLE GLAND. < Fig 7-12a > After uniting four TRUSS Screws, M4X10, please open AC UNIT COVER. < Fig 7-12b > As you are conferring the explanation on the attached sticker, you can connect SELECT terminal with VOLTAGE SELECTION TERMINAL BLOCK and fix it with a BOLT. SELECT < Fig 7-12c > 35 SIMULINE INC. . After you push Electric Cable through Cable Gland Cap Nut, you can connect it with the main input electrical terminal stand. [. . . ] PBR-0460 PBR-0470 PBR-0480 PBR-0451 MET-03-025P PBR-0452 PBR-0453 ECB-05-024P WR06-020HNB W-FL06HNB W-SP06HNB TR04-008NNB FH-04NSN RW04-012NNB 73 SIMULINE INC. . 4. Ass'y Sensor(L) (PBR-0500) 201 2 3 4 101 201 2 202 2 203 3 2 Section A-A 203 4 102 2 5 A A 1 ITEM No. 1 2 3 4 5 101 102 201 202 203 DESCRIPTION SENSOR FRAME (L) SENSOR COVER - L SENSOR ADJUST BRAKET-L FOOT SENSOR FIX BRKT REFLECTOR SUPPORT PLATE PRK 25B[LEUZE] MECHATEM REFLECTOR [KEO SAMG] ROUND SEMS SCREW M3X8L ROUND SEMS SCREW M3X20L ROUND SEMS SCREW M4X8L PART No. PBR-0501 PBR-0502 PBR-0503 PBR-0504 PBR-0505 ESU-05-R046P ESU-05-R047P SR03-008NNB SR03-020NNB TR04-008NNB 74 SIMULINE INC. . 5. [. . . ]