User manual SEGA AFTERBURNER STD

[. . . ] 420-0002-01UK 1st Printing AFTER BURNER CLIMAX OWNER'S MANUAL 420-0002-01UK OWNER'S MANUAL IMPORTANT © SEGA Produced under license from Boeing Management Company. Boeing, McDonnell Douglas, McDonnell, Douglas, North American Aviation, their distinctive airplane liveries, logos and product markings are among the trademarks owned by Boeing. F-14D Super Tomcat, F-5E Tiger II, A-10A Thunderbolt II, B-2A Spirit, and CVN-65 Enterprise are trademarks of Northrop Grumman Systems Corp. and are used under a license to Sega Corporation. ¥ Before using this product, read this manual carefully to understand the contents herein stated. [. . . ] If anyone is near the product, they could collide with the product or come in contact with it accidentally. Accidents could also occur if tools or other items fly off the product. · · · Be careful when handling the plastic parts. Failure to observe this may cause injury or damage due to fragments, etc. Do not attempt to replace billboard fluorescent lamps while standing on the base. If you should misstep while working, you could stumble or fall down. This product has 1 fluorescent lamp in the billboard 1) Cut off the power supply. 2) Remove 4 truss screws from atop the billboard. 3) Remove the billboard lid and replace the fluorescent lamp. 39 4. 4 PERIODIC INSPECTION · Once a year, check to see if power cords are damaged, the plug is securely inserted, dust is accumulated between the socket outlet and the power plug, etc. Using the product with accumulated dust in the interior may cause fire or electric shock. If wetness occurs for any reason, do not use the product until it has completely dried. · Once a year, request the office shown on this manual or the dealer from whom the product was originally purchased to perform the internal cleaning. Using the product with accumulated dust in the interior may cause fire or other accidents. · Once a year, request the office shown in this manual or the dealer from whom the product was originally purchased to perform routine maintenance on moving mechanisms. · There is the danger of accidents involving electrical shorts circuits or fire caused by factors such as the deterioration of insulation in electrical and electronic equipment over time. Check that there are no abnormalities such as odors from burning. If there is only enough space for ventilation in the area reserved for product installation and operation, do not begin maintenance work until space has also been set aside for maintenance. Such work cannot be performed safely and thoroughly in narrow spaces. In order to maintain the performance of this product and operate it safely, inspect the following items routinely and perform maintenance. The player directly touches and manipulates the control stick and throttle lever with his/her hands. Clean these components as necessary and provide hand towels, etc. , so that players will be comfortable while playing. The service manual referred in the table is the LINDBERGH service manual, which is provided separately. 40 PERIODIC CHECK TABLE ITEMS CABINET DESCRIPTION Confirm that adjusters contact floor Screen cleaning MONITOR Check screen adjustment Inspection of volume, switch CONTROL STICK Greasing Inspection of volume, switch THROTTLE LEVER Greasing Inspection of volume ROLL VOLUME Greasing Inspection of coin switch COIN SELECTOR Coin insertion test Coin Selector cleaning Check of board information GAME BOARD Check of settings FLUORESCENT LAMP ELECTRICAL/ ELECTRONIC PARTS POWER CABLE CABINET INTERIOR CABINET SURFACES MOVING MECHANISMS CLEANING THE CABINET SURFACE When the cabinet surfaces become dirty, remove stains with a soft cloth soaked in water or diluted (with water) chemical detergent and then wrung dry. To avoid damaging the finish, do not use such solvents as thinner, benzene, etc. (other than ethyl alcohol) or abrasives (bleaching agent and chemical dust-cloth). Some general-purpose household, kitchen, and furniture cleaning products may contain strong solvents that degrade plastic parts, coatings, and print. Before using any cleaning product, read the product's cautionary notes carefully and test the product first on a small area that is not highly visible. Inspection of lighting fixtures Inspection Inspection, Cleaning Cleaning Cleaning Maintenance 1 month As appropriate As appropriate 1 year 1 year As appropriate 1 year 3 months 1 month 1 month 3 months 1 month 3 months 1 month 3 months 1 month PERIOD Daily Weekly Monthly or when moving 1 month 41 4. 5 TROUBLESHOOTING · If an error message is displayed, have the problem looked at by a store maintenance person or a technician. [. . . ] Return to BACKUP DATA CLEAR Screen. 74 7 NETWORK PLAY · Linking machines should only be carried out by QUALIFIED SERVICE PERSONNEL. · Do not stress/over-bend the fibre optic cables, as this will affect their performance. · · · · Before starting to work, ensure that the power switch is OFF. Damaged wires may cause electric shock or short circuit or present a fire risk. Touching places not designated can cause electric shock or short circuit. [. . . ]