User manual SEARS CLEANMORE 175-8535280

[. . . ] To minimize possible shock hazard it must be plugged into a mating 3-prong grounding type wall receptacle, grounded in accordance with the National Electrical Code and local codes and ordinances. lf a mating wall receptacle is not available, it is the personal responsibility and obligation of the customer to have a properly , grounded 3-prong wall receptacle installed by a qualified electrician. The power cord should always be disconnected from the electrical outlet before the recovery tank is emptied, the solution tank is refilled or the cleaner is serviced in any way. DO NOT store this cleaner in an area which may reach freezing temperatures. [. . . ] lf carpet has previously been cleaned. with regular it 'may be n-ecessary to add defoamer, tnlh-poo, '*e, to the recovery tank by raising Foimuta t-iiJtrei ani titting Power liead from the Re' -overy Tank. Follow directions on bottle' LATCH ftcunE 9 POWER HEAD POWER SWlTCtl CARPET CLEANING POWER CORD See Figure 10' POWEF COFD 1. Unwrap Power Cord from Power Head and plug into electrical outlet. 2. Turn Power Switch on' HSURE 10 TESTING FOR SOLUTION SPRAY See Figure 11' 1. Pull Solution Release Trlgger on Angle Wand' See Detait "A" Figure 11' 3. Observe Floor Nozzle to make sure cleaning - Jorriion is being sprayed evenly from two points' NOTE: lf solution is not being sprayed from both points, refer to "service Hinis" section of this manual. Page 6 OPERATION CLEANING THE CARPET See Figures 12 and 13. Solution Dispensing Stroke 1. While exerting light pressure down on floor nozzle, depress Solution Release Trigger and slowly pull Floor Nozzle towards you. NOTE: Do not overwet carpet - See "Rules For Safe Operation" on page 2, Rule #13. Solution Recovery Stroke 1. To accomplish this, release the Solution Trigger and lift the Floor Nozzle off carpet, return Floor Nozzle to point where you dispensed cleaning solution, and recover dirty solution. WHEN TO EMPTY RECOVERY TANK See Figure 14. During normal operation, your cleaner may stop recovering solution from your carpet. No solution visibly being recovered by your floor nozzle. EXHAJSI 3. No air coming from the exhaust part of your cleaner. When this occurs: 1. The Recovery Tank is full and the Float Valve in the recovery tank has been activated. The Recovery Tank has foam in the tank and the float valve has been activated. Page 7 Figure 14 OPERATION HOW TO EMPTY RECOVERY TANK See Figure 15. L Turn Power Swilch "off" tion Tank and recovery tank. Disconnect large vacuum hose by depressing the Lock Button and remove. Push Tab inward on Plastic Coupling and remove plastic insert and tubing. Note: lf foam is observed in Recovery Tank, add Sears Defoamer (Formula #2). [. . . ] (2) Armatu re eomplete"wi fan Brush Assembiy (2) Brush Clamp (2i Screw, Brush Mtg. (2) Bearing Retainer Field Core Wound Self-Aligning Bearing - "O" Ring 82 83 84 85 86 Shaft-Pump Washer-Stainless Stl. Screw, Motor to Container (4) Retaini ng Ri ng-External Washer Washer Hex Nut Magnet Housing Washer-Phenolic Self-Aligning Bearing Washer-Phenolic 14 SEARS CLEANMORE HOME CLEANING SYSTEM 101 - MODEL 175. 8535280 102 ---100 Figure C KEY 87 88 89 90 , ou-f-ff rotX- -'r''"--1o8 DESCRIPTION PT. NUMBER 643731-005 644037-002 644152-002 643171-002 644153-004 643445-000 644830-001 643444-000 644151-002 643171. 002 643446-000 644', t62-002 643572-004 644038-003 644037-002 643570-014 644047-002 644909-002 643428-001 640145-007 643454. 002 643429-933 643526-002 643571-005 644848-002 643502-005 642976-011 660300-104 90A 91 91A 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 Strap-Tubing (2) Nut-Ferrule Lever (Trigger) "O" Ring Curved Wand Washer-Stainless Stl. [. . . ]