User manual SEAGATE SCSI

[. . . ] Pleas e refer to your computer us er manual for more information. (see kit package for details) T hank you for selecting a Maxtor hard drive storage product. Maxtor's goal is to provide you with the most up-to-date product possible , and we are constantly enhancing our software and documentation to better meet your needs. Please visit our website at www. maxtor. com to view the latest that Maxtor has to offer! Tools for Installation The following tools are needed to ins tall your new M axtor hard drive: S mall Phillips head s crew driver S mall pair of pliers or tweezers Your computer us er manual Operating s ys tem s oftware 2 Drive ID ID 0 ID 1 ID 2 ID 3 ID 4 ID 5 ID 6 ID 7 ID 8 ID 9 ID 10 ID 11 ID 12 ID 13 ID 14 ID 15 Dr ive Jum p e r S et up Other J umper Settings T P - T erm ination Pow er (12 Pin Option Connector) Pins 11-12 T ermination power ensures that there is a sufficient power level along the entire S CS I bus . [. . . ] DS - Delay S pin Dis able Delay S pin: No jumper acros s pins 15-16 (factory default). Dis abling Delay S pin allows the drive to s pin up when the s ys tem is powered up. E nable Delay S pin: J umper across pins 15-16 This setting will prevent the drive from spinning up until it receives a Start Unit command from a S CS I hos t adapter. M os t S CS I hos t adapters have the S tart Unit command enabled by default in the host adapter B IOS. Enabling Delay Spin is only necessary when you are starting multiple devices at power on. S CS I ID Pin numbers 1-8 are typically referred to in pairs as A0 (pins 1 and 2), A1 (3, 4), A2 (5, 6), A3 (7, 8). The jumper pairs will allow configuration of S CS I ID's 0 to 15. All S CS I devices must have an individual ID on the S CS I bus (there is no M aster/S lave setting). Fault LE D and B us y Out J um pers Typical installations do not require the use of the Fault LE D and B usy Out jumpers. The B usy Out signal is usually supplied through the PCI bus to the PC motherboard's B usy indicator LE D. If connecting the B usy Out jumper for a drive installed in an external case, please refer to the wiring documentation supplied by the manufacturer of the case. Connection of the Fault LE D is not recommended in internal or external installations. Pin 1 Pin 2 Pin 1 Pin 2 Configure the Drive J umpers If specific jumper options are needed for your system configuration, refer to the illustrations and definitions provided in this section. SCSI ID 0 SCSI ID 1 SCSI ID 2 SCSI ID 3 NOT USED FAULT LED GROUND GROUND BUSY LED GROUND TERM POWER SCSI ID 3 SCSI ID 2 SCSI ID 1 SCSI ID 0 BUSY LED -/+ WRT PROTECT STAGGER SPIN DELAY SPIN SCSI ID J umper Settings ID Bit O OFF ON OF F ON OFF ON OFF OFF ON OFF ON OFF ON OFF ON ID Bit 1 OFF OFF ON ON OFF OFF ON OFF OFF ON ON OFF OFF ON ON D Bit 2 FF FF FF FF N N N OFF OFF OFF OFF ON ON ON ON ID Bit OF OF OF OF OF OF OF ON ON ON ON ON ON ON ON +5 V Pin 11 Pin 12 SINGLE ENDED Pin 17 Pin 18 RESERVED FOR SCSI HOS T 4 Pin Power Connector 12 Pin Option Connector M axtor S CS I drives typically s hip from the factory with jumpers s et to S CS I ID 6, and termination power jumped. A ttention: The R ear J umper Option Connector is an OE M s pecific connector. M os t ins tallations w ill never us e the jumper options on this connector. Alw ays configure the drive us ing the jumpers at the Front J um per Option Connector . 68 Pin SCSI Connector N ote: M axtor LVD S CS I drives do not s upport on-board termination. M axtor recommends the us e of Active LVD terminators and 68-pin tw is ted pair cabling. S C S I hos t adapter manufacturers us ually s upply proper cabling and termination with the purchas e of an LVD S C S I hos t adapter. 3 Drive Install Installing 5. 25-inch Mounting Brackets If the hard drive will be installed in a 5. 25inch device bay, attach mounting brackets (available separately) to the hard drive as shown in the figure below. Installing Drive Inside of Y our Computer System M ake s ure your com puter is pow ered dow n before ins talling the drive. The following illus trations are of typical computer s ys tems and hard drive mounting s tyles . [. . . ] If your system is not capable of booting from a CD, you can download bootable W indows XP installation floppies from M icrosoft's website at www. microsoft. com M acintosh: M ost non-Apple branded hard drives can be formatted using the Drive Setup utility included in M ac OS 8. 6 and above. M ac OS versions before 8. 6 will require a third-party hard drive utility such as FW B Hard Disk Toolkit (www. fwb. com) or Intech Hard Disk SpeedTools (www. intechusa. com) to partition and initialize the drive. Please visit the FW B or Intech website for details on these non-M axtor software products. Changes are periodically made to the information herein which will be incorporated in revised editions of the publication. [. . . ]