User manual SEAGATE SAVVIO FC

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual SEAGATE SAVVIO FC. We hope that this SEAGATE SAVVIO FC user guide will be useful to you.


SEAGATE SAVVIO FC : Download the complete user guide (1412 Ko)

Manual abstract: user guide SEAGATE SAVVIO FC

Detailed instructions for use are in the User's Guide.

[. . . ] Product Manual Savvio FC ST973401FC ST936701FC 100293077 Rev. D, August May 2007 Seagate, Seagate Technology and the Wave logo are registered trademarks of Seagate Technology LLC in the United States and/or other countries. Savvio, SeaTools and SeaTDD are either trademarks or registered trademarks of Seagate Technology LLC or one of its affiliated companies in the United States and/or other countries. All other trademarks or registered trademarks are the property of their respective owners. [. . . ] See paragraph 6. 2. 1, "Conducted noise immunity. " Specified voltage tolerance includes ripple, noise, and transient response. Operating condition is defined as random 8 block reads at: 258 I/Os per second (ST973401FC at 1Gbit operation) 259 I/Os per second (ST973401FC at 2Gbit operation) 258 I/Os per second (ST936701FC at 1Gbit operation) 258 I/Os per second (ST936701FC at 1Gbit operation) During idle, the drive heads are relocated every 60 seconds to a random location within the band from three-quarters to maximum track. General DC power requirement notes. Minimum current loading for each supply voltage is not less than 1. 2% of the maximum operating current shown. Where power is provided to multiple drives from a common supply, careful consideration for individual drive power requirements should be noted. Where multiple units are powered on simultaneously, the peak starting current must be available to each device. Parameters, other than spindle start, are measured after a 10-minute warm up. D 6. 2. 1 Conducted noise immunity Noise is specified as a periodic and random distribution of frequencies covering a band from DC to 10 MHz. Maximum allowed noise values given below are peak-to-peak measurements and apply at the drive power connector. +5V 100 hz to 20 Mhz 100 hz to 8 Khz 8 Khz to 20 Khz 20 Khz to 5 Mhz 250mV 800 mVpp 450 mVpp 250 mvpp +12V 6. 2. 2 Power sequencing The drive does not require power sequencing. The drive protects against inadvertent writing during power-up and down. 6. 2. 3 Current profiles The +12V and +5V current profiles for the ST973401FC and ST936701FC models are shown below in the following figures. T0 T1 T2 T3 Power is applied to the drive. Spindle begins to accelerate under current limiting after performing internal diagnostics. Spindle is up to speed and the Head-Arm restraint is unlocked. Note: All times and currents are typical. Typical ST973401FC drive +12V current profile Savvio FC Product Manual, Rev. Typical ST936701FC drive +12V current profile 28 Savvio FC Product Manual, Rev. Typical ST936701FC drive +5V current profile Savvio FC Product Manual, Rev. D 29 6. 3 Power dissipation ST973401FC Typical power dissipation under idle conditions in 1Gb operation is 6. 6 watts (22. 5 BTUs per hour). Typical power dissipation under idle conditions in 2Gb operation is 6. 9 watts (23. 7 BTUs per hour) To obtain operating power for typical random read operations, refer to the following I/O rate curve (see Figure 6). Locate the typical I/O rate for a drive in your system on the horizontal axis and read the corresponding +5 volt current, +12 volt current, and total watts on the vertical axis. To calculate BTUs per hour, multiply watts by 3. 4123. ST973401FC DC CURRENT/POWER vs THROUGHPUT (1GB) Random 8 Block Reads 1 . 200 1 2. 00 5Vo lt A 1 Volt A 2 Watts 1 . 000 1 0. 00 0. 800 8. 00 Power (watts) Amperes 0. 600 6. 00 0. 400 4. 00 0. 200 2. 00 0. 000 0. 0 50. 0 1 00. 0 1 50. 0 200. 0 250. 0 0. 00 300. 0 I/Os per Second Figure 6. input/output operations per second at 1 Gbit 1 . 200 ST973401FC DC CURRENT/POWER vs THROUGHPUT (2GB) Random 8 Block Reads 1 2. 00 5Vo lt A 1 Volt A 2 Watts 1 . 000 1 0. 00 0. 800 8. 00 Power (watts) Amperes 0. 600 6. 00 0. 400 4. 00 0. 200 2. 00 0. 000 0. 0 50. 0 1 00. 0 1 50. 0 200. 0 250. 0 0. 00 300. 0 I/Os per Second Figure 7. input/output operations per second at 2 Gbit 30 Savvio FC Product Manual, Rev. D ST936701FC Typical power dissipation under idle conditions in 1Gb operation is 6. 2 watts (21. 2 BTUs per hour). [. . . ] Submit pricing requests, orders and returns through a single, password-protected Web interface-anytime, anywhere in the world. spp. seagate. com spp. seagate. com supports Seagate resellers with product information, program benefits and sales tools. You may register for customized communications that are not available on the web. These communications contain product launch, EOL, pricing, promotions and other channel-related information. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE SEAGATE SAVVIO FC




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual SEAGATE SAVVIO FC will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.