User manual SEAGATE MOMENTUS BLADE SERVER

[. . . ] Momentus Blade Server ST94811AB Momentus Blade Server ST94811AB ©2004, Seagate Technology LLC All rights reserved Publication number: 100339697, Rev. A June 2004 Seagate and Seagate Technology are registered trademarks of Seagate Technology LLC. DiscWizard, SeaTools, SeaFONE, SeaBOARD, SeaTDD, 3D Defense System and the Wave logo are either registered trademarks or trademarks of Seagate Technology LLC. Other product names are registered trademarks or trademarks of their owners. [. . . ] You may find helpful the following booklet prepared by the Federal Communications Commission: How to Identify and Resolve Radio-Television Interference Problems. Refer to publication number 004-000-00345-4. Momentus Blade Server Product Manual, Rev. A 3. 0 Configuring and mounting the drive This section contains the specifications and instructions for configuring and mounting the drive. 3. 1 Handling and static discharge precautions After unpacking, and before installation, the drive may be exposed to potential handling and electrostatic discharge (ESD) hazards. Observe the following standard handling and static-discharge precautions: Caution: · Keep the drive in the electrostatic discharge (ESD) bag until you are ready for installation to limit the drive's exposure to ESD. · Before handling the drive, put on a grounded wrist strap, or ground yourself frequently by touching the metal chassis of a computer that is plugged into a grounded outlet. Wear a grounded wrist strap throughout the entire installation procedure. · Always rest the drive on a padded, antistatic surface until you mount it in the computer. · Do not touch the connector pins or the printed circuit board. · Do not remove the factory-installed labels from the drive or cover them with additional labels. Some factory-installed labels contain information needed to service the drive. Other labels are used to seal out dirt and contamination. 3. 2 3. 2. 1 Jumper settings Master/slave configuration Use the options jumper block shown in Figure 3 to configure the drive for operation. This jumper block is the 4pin header adjacent to pins 1 and 2 of the I/O signal pins. For additional information about using the Cable select option, see Section 3. 2. 2. The "Master or single drive" option is the factory default setting. Drive is master (or single drive) Drive is slave Cable select Figure 3. A 15 3. 2. 2 Cable-select option Computers that use cable select determine the master and slave drives by selecting or deselecting pin 28, CSEL, on the interface bus. Master and slave drives are determined by their physical position on the cable. Refer to your computer manual to determine whether your computer supports this option. 3. 3 Drive mounting You can mount the drive using four screws in the side-mounting holes or four screws in the bottom-mounting holes. Follow these important mounting precautions when mounting the drive: · Allow a minimum clearance of 0. 030 inches (0. 76 mm) around the entire perimeter of the drive for cooling. · Do not overtighten the mounting screws (maximum torque: 4. 0 inch-lb). · Four (4) threads (0. 080 inches) minimum screw engagement recommended. 3. 945 +/-0. 0098 (100. 2 +/-. 25) 0. 490 +/- . 010 (12. 446 +/- . 254) 0. 680 +/- . 010 (17. 27 +/- . 254) . 157 (3. 9878) . 399 (10. 135) 2. 750 +/- . 0098 (69. 85 +/- . 25) Breather Hole Do not cover or seal. inches (mm) Recommended case temp. measurement location 3. 567 (90. 602) . 551 (13. 99) 2X M3 X 0. 5-6H Mounting holes Both sides . 12 min. full thread . 374 +/- . 0078 (9. 5 +/- . 2) 2X . 118 Both sides . 551 (13. 99) 3. 567 (90. 60) 4X M3 X 0. 5-6H Mounting holes . 10 min. [. . . ] Have your drive's "ST" model number and serial number available. Authorized Service Centers In some locations outside the US, you can contact an Authorized Service Center for service. USA/Canada/Latin America Support Services Presales Support Call Center Americas Toll-free 1-877-271-32851 Toll-free 1-800-SEAGATE2 Toll-free 1-800-468-34724 Direct dial +1-405-324-47301 Direct dial +1-405-324-47003 Direct dial +1-405-324-47204 FAX +1-405-324-4704 FAX +1-405-324-4702 FAX / Internet +1-405-324-4722 Technical Support Call Center Americas Warranty Service Call Center USA, Mexico and Latin America Canada Memofix5 Brazil MA Centro de Serviços5 1-800-636-6349 +1-905-660-4936 +1-905-660-4951 www. memofix. com -- +55-21-2509-7267 +55-21-2507-6672 www. mainformatica. com. br/produtos. htm 1Hours 2For of operation are 8:00 A. M. to 6:00 P. M. , Monday through Friday (Central time) product-specific phone number 3Hours of operation are 8:00 A. M. to 8:00 P. M. , Monday through Friday (Central time) 4Hours of operation are 8:30 A. M. to 5:30 P. M. , Monday through Friday (Central time) 5Authorized Service Center 26 Momentus Blade Server Product Manual, Rev. [. . . ]