User manual SEAGATE DB 35
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual SEAGATE DB 35. We hope that this SEAGATE DB 35 user guide will be useful to you.
Manual abstract: user guide SEAGATE DB 35
Detailed instructions for use are in the User's Guide.
[. . . ] DB35 Series
ST3400832ACE ST3300831ACE ST3250823ACE ST3200826ACE
DB35 Series
ST3400832ACE ST3300831ACE ST3250823ACE ST3200826ACE
©2005, Seagate Technology LLC All rights reserved Publication number: 100347671, Rev. B May 2005 Seagate and Seagate Technology are registered trademarks of Seagate Technology LLC. SeaTools, SeaFONE, SeaBOARD, SeaTDD, and the Wave logo are either registered trademarks or trademarks of Seagate Technology LLC. Other product names are registered trademarks or trademarks of their owners. [. . . ] B
3. 0
Configuring and mounting the drive
This section contains the specifications and instructions for configuring and mounting the drive.
3. 1
Handling and static discharge precautions
After unpacking, and before installation, the drive may be exposed to potential handling and electrostatic discharge (ESD) hazards. Observe the following standard handling and static-discharge precautions: Caution: · Keep the drive in the electrostatic discharge (ESD) bag until you are ready for installation. · Before handling the drive, put on a grounded wrist strap, or ground yourself frequently by touching the metal chassis of a computer that is plugged into a grounded outlet. Wear a grounded wrist strap throughout the entire installation procedure. · Always rest the drive on a padded, antistatic surface until you mount it in the computer. · Do not touch the connector pins or the printed circuit board. · Do not remove the factory-installed labels from the drive or cover them with additional labels. Some factory-installed labels contain information needed to service the drive. Other labels are used to seal out dirt and contamination.
DB35 Series Product Manual, Rev. B
15
3. 2
Breather filter hole precautions
This section contains information regarding the precautions which should be taken regarding the breather filter hole in Seagate hard disc drives. Proper precautions should be taken to ensure full functionality and prevent possible damage to the drive.
Breather hole Do not cover or seal this hole.
Figure 3
Breather filter hole location
Caution: Do not cover, seal, or insert any object into this hole. This hole has two purposes: · To allow condensation inside the hard disc to escape · To allow air pressure inside the hard disc to equalize with ambient pressure Note. If this hole is covered, sealed, or penetrated by any object, drive reliability may be compromised and could lead to permanent damage--doing so voids the warranty.
16
DB35 Series Product Manual, Rev. B
3. 3
3. 3. 1
Jumper settings
Master/slave configuration
The options jumper block shown in Figure 4 is used to configure the drive for operation. It is the 8-pin dual header between the interface connector and the power connector. Use the following settings to configure the drive as a master or a slave. The drive is configured at the factory for a master or single-drive operation with a jumper set on pins 7 and 8. Use this jumper setting only if the drive does not work as a master with no jumpers installed.
Options jumper block
Master or single drive Drive is slave
Master with non ATAcompatible slave
Cable select
Limit drive capacity to 32 Gbytes
7531
8642
Figure 4
Circuit Board
Master/slave jumper settings
3. 3. 2
Cable-select option
Computers that use cable select determine the master and slave drives by selecting or deselecting pin 28, CSEL, on the interface bus. Master and slave drives are determined by their physical position on the cable. To enable cable select, set a jumper on pins 5 and 6 as shown in Figure 4. Refer to your computer manual to determine whether your computer supports this option. 3. 3. 3 Alternate capacity jumper
Some older computers may "hang" at startup if their BIOS detects a disc drive with a capacity greater than 32 Gbytes. [. . . ] Resellers or end users of drive products should contact their place of purchase or one of the Seagate CSO warranty centers for assistance. Have your drive's "ST" model number and serial number available.
Authorized Service Centers
In some locations outside the US, you can contact an Authorized Service Center for service.
30
DB35 Series Product Manual, Rev. B
USA/Canada/Latin America Support Services Seagate Service Centers
Presales Support
Call Center Americas Toll-free 1-877-271-32851 Toll-free 1-800-SEAGATE2 Direct dial +1-405-324-47301 Direct dial +1-405-324-47002 FAX +1-405-324-4704 FAX +1-405-324-3339
Technical Support
Call Center Americas
Customer Service Operations
Warranty Service
Call Center USA, Canada, Mexico and Latin America Brazil Jabil Inudstrial Do Brasil LTDA4 Toll-free 1-800-468-34723 Direct dial -- FAX / E-mail +1-956-664-4725
--
+55-11-4191-4761
+55-11-4191-5084 SeagateRMA. br@jabil. com
1Hours 2Hours
of operation are 8:00 A. M. to 6:00 P. M. , Monday through Friday (Central time) of operation are 8:00 A. M. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE SEAGATE DB 35
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual SEAGATE DB 35 will begin.