User manual SAS ENTERPRISE MINER 6.1 SINGLE-USER INSTALLATION GUIDE

[. . . ] SAS Enterprise Miner 6. 1 Single-User Installation Guide ® TM The correct bibliographic citation for this manual is as follows: SAS Institute Inc. SAS® Enterprise Miner 6. 1: Single-User Installation Guide Copyright © 2009, SAS Institute Inc. , Cary, NC, USA All rights reserved. For a Web download or e-book: Your use of this publication shall be governed by the terms established by the vendor at the time you acquire this publication. Use, duplication, or disclosure of this software and related documentation by the U. S. [. . . ] When the laptop is running without a network connection, then the laptop machine name is the short local host name (for example, mymachine). SAS uses the value of Short Local Host Name for labeling purposes only and it is never used to do anything related to networking. 4 16 Install and Configure SAS Enterprise Miner Interactively 4 Chapter 2 18 On the Single-User Account page, enter a Windows account that is known to the machine and is a member of the Windows Administrators group. (This is the account with which you will log on to the SAS 9. 2 analytics clients that you are installing. ) 19 On the E-mail Server page, enter the port and host name for an SMTP e-mail server that the SAS Metadata Server uses to send e-mail alerts to an administrator if journaling issues arise. The SAS Deployment Wizard also uses this e-mail server as the default for the SAS Application Server to provide e-mail services to various SAS clients. Deploying SAS Enterprise Miner in Single-User Mode 4 Install and Configure SAS Enterprise Miner Interactively 17 Note: If you do not know the name of your SMTP e-mail server, or do not have such a server, then entering a dummy value enables the installation to continue. However, you will not receive e-mail notifications should your metadata server run low on disk space. 4 For more information, see "Overview of Adding or Modifying E-Mail Settings for SAS Application Servers" in the SAS Intelligence Platform: Application Server Administration Guide. 20 The SAS Deployment Wizard has finished collecting installation and configuration input. This is the last opportunity to go back and change any information you have provided on previous pages before the wizard begins writing to your system. Make one of the following choices: 3 Click Start to begin installing SAS files and writing the configuration to the current machine. 3 Click Back to navigate to earlier wizard pages to change installation and configuration information previously entered. Note that you will lose installation and configuration information previously entered. 18 Install and Configure SAS Enterprise Miner Interactively 4 Chapter 2 21 If this is a first-time SAS 9. 2 deployment, the System Requirements Wizard runs and requires you to provide input. This is the last interactive input required from you, unless a configuration error occurs. When you see a page similar to the following, the SAS Deployment Wizard is finished: Deploying SAS Enterprise Miner in Single-User Mode 4 Install and Configure SAS Enterprise Miner Interactively 19 22 Click Next. The Additional Resources page lists several URLs that you can visit to obtain things such as technical support and product training. 23 Click Finish. Your Web browser should appear. If you had any configuration errors, you should see ConfigurationErrors. html. Otherwise, you should see Instructions. html. 20 Review SAS Deployment Wizard Documents 4 Chapter 2 24 Proceed to the section, "Review SAS Deployment Wizard Documents" on page 20 to examine the SAS Deployment Wizard output to troubleshoot any configuration errors and complete any necessary manual configuration steps. Note: SAS requires that the installer account have the Windows user right Log on as batch job assigned. If this right is not assigned, then the SAS Deployment Wizard does it for you. Check Instructions. html to see whether the wizard assigned the Log on as a batch job right. If this assignment was made, then you must reboot your machine before using SAS Enterprise Miner. 4 25 When you are finished, be sure to back up your metadata repository and your SAS configuration directory before you perform any post-deployment wizard configuration. 3 Make a backup copy of your SAS 9. 2 configuration directories by using your site-approved method. Your SAS configuration directories are all the child directories beneath the path that you specified earlier in this procedure on the Specify Configuration Information wizard page. For more information, see "Best Practices for Backing Up and Restoring Your System" in the SAS Intelligence Platform: System Administration Guide. 26 Be sure to restart any SAS Windows services that you stopped for purposes of creating a backup. Review SAS Deployment Wizard Documents During configuration of SAS 9. 2, the SAS Deployment Wizard creates documents that can help you identify any remaining configuration tasks and errors. [. . . ] For example, content in a section heading has a different meaning from content in a database table. Short form: XML. Java a set of technologies for creating software programs in both stand-alone environments and networked environments, and for running those programs safely. Java is a Sun Microsystems trademark. login a SAS copy of information about an external account. Most logins do not include a password. metadata identity a metadata object that represents an individual user or a group of users in a SAS metadata environment. [. . . ]