User manual SANYO VPC-SX560E

[. . . ] i This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. [. . . ] Follow the instructions on the screen to format the card. SETUP Shooting without a card installed i When a card is installed, images are recorded to and played back from the card. When no card is installed, images are recorded to and played back from the camera's internal memory. When the camera is turned on with no card installed, the internal memory icon is shown on the monitor to let you know that the images you capture will be saved to the camera's internal memory. English 10 TURNING THE CAMERA ON AND OFF Turning on the camera 1 Press the ON/OFF button for at least 1 second. ON/OFF button Turning off the camera 1 Press the ON/OFF button for at least 1 second. h The camera turns off. HINT To adjust the operation sounds i If you turn on the camera by pressing the ON/OFF button while holding down the [I] arrow key, the screen to change the operation sounds will appear. 11 English Turning on the camera when the power save (sleep) mode is active In order to preserve battery pack power, the power save (sleep) function will automatically turn off the camera after about 2 minutes of no use during shooting, or about 2 minutes of no use during playback. i When the power save mode is active, you can restore the power by any of the following methods: h Press the ON/OFF button. h Press the SET button. SETUP English 12 CAUTION If the K icon appears. . . i When a picture is taken, the date and time it was captured are recorded with it. If the date and time settings have not been completed (page 14), the date and time cannot be recorded with the captured images. For this reason, immediately after the camera is turned on, the "Set date and time" reminder briefly appears, after which the K icon is shown on the Recording Screen. To have the date and time recorded with the images, please complete this setting before capturing images. <Caution> i Due to the characteristics of the camera, the outer surface may become warm during use, but this does not indicate a malfunction. i The Setup Menu appears when the [?] button is kept pressed for at least 1 second. i Press the [?] button to cancel the Setup Menu, and then briefly press the [?] button again. 21 English HINT What is the camera focusing on?Target mark i A target mark & on the monitor shows the area the camera is focusing on. i The camera automatically determines the correct focus by measuring from 9 different focus points within the shooting area. If the target mark is at a position that is F3. 1 1/4 different from the point you wish to focus on, you can refocus, for Camera shake icon example, by changing the shooting Shutter speed angle. Aperture i The large target mark appears when the camera focuses on a wide area in the center of the screen. i During still image shooting, if the shutter speed is slow and the possibility that the image may be blurred due to camera shake becomes high, the camera shake icon may appear on the monitor. i When shooting in dimly lit conditions, it may take some time to save the data to the card. SHOOTING English 22 SHOOT A STILL IMAGE WHILE RECORDING A VIDEO CLIP You can capture a still image (a single-shot) while recording a video clip. 1 2 3 4 Turn on the camera (page 11). Press the [ ] button. [ ] button (Video recording button) When you see a scene you'd like to capture as a still image, press the [ ] button. Press the [ ] button to end the video clip recording. [ ] button (Photo shooting button) 2M REC 00:09 HINT i When the remaining video recording time becomes approximately 30 seconds, it will no longer be possible to capture a still image while recording a video clip. The exact remaining recording time at which this occurs will differ depending on the subject and on the recording size, as well as on the video clip recording mode. [. . . ] 2-second delay, 10-second delay Ambient Temperature 0 to 40 °C (32 to 104°F) (operation) environment ­20 to 60 °C (­4 to 140°F) (storage) Humidity 30 to 90% (operating, no condensation) 10 to 90% (storage, no condensation) Power supply Battery pack Li-ion battery pack (DB-L80) ×1 (supplied) Power consumption 3. 4 W (When using the Li-ion battery during recording) Dimensions (excluding protrusions) 63. 1 (W) × 22. 0 (D) × 110. 8 (H) mm 2. 48 (W) × 0. 87 (D) × 4. 36 (H) in. 105 g (3. 7 oz. ) (camera only [without battery pack and card]) Image stabilizer 43 English Camera connectors USB terminal mini HDMI terminal Dedicated regrouped jack USB 2. 0 High Speed Video output Total number of scan lines (effective number of scan lines): 750p (720p)/1125i (1080i)/525p (480p) Audio output: L-PCM 48 kHz sampling Battery life Shooting Still image shooting mode Video clip recording mode Playback Approx. 170 images: CIPA standard (when a SanDisk 2 GB SD Memory Card is used) Approx. 240 minutes: Monitor on, continuous playback i Until battery pack runs out when using a fully charged battery pack at a 25 °C (77 °F) ambient temperature. [. . . ]