User manual SANYO VPC-S500

[. . . ] FCC STATEMENT (For customers in USA) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for Class B digital devices, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. [. . . ] Flash does not fire in this mode. · After one shot is taken, the self-timer mode is turned off. · If you wish to take another image using the self-timer, repeat these steps. EN-32 Adjusting the Exposure (EV Compensation) You can manually adjust the exposure determined by the digital camera. Use this mode when the proper exposure cannot be obtained, for example, when the contrast (difference between bright and dark areas) between the subject and the background is extremely high. The EV compensation value can be set in the range from -2. 0EV to +2. 0EV. Press the four-way controller ( / ) and use to set the range of EV compensation value from -2. 0EV to +2. 0EV. Press the button to confirm the setting. EV ±0. 0 0. 0 Select : Set : EN-33 Setting White Balance This feature lets you make adjustments to compensate for different lighting types according to your shooting conditions. Use the four-way controller ( ) to select the desired white balance setting, then press the button to confirm. Press the shutter release button to capture the image. Mode1 Mode2 Mode3 Image Si Im ge Size Quality W. Balanc Auto Aut uto Daylight Cloudy Tungsten Tungste ungsten Cancel : Select : W. Balanc Fluorescent Fluo escent luorescen Cancel : Select : EN-34 PLAYBACK MODE - THE BASICS Viewing Images You can display the still images one by one. Rotate the mode dial to , , , , 100-0001 , or and turn your camera on by pressing the power switch. To view the next image, press the four-way controller ( ). · For protected images/movie clips, mark will be displayed. Refer to the section in this manual titled "Protecting Images/Movie Clips" for further details. · For images selected for printing with DPOF setting, mark will be displayed. (Refer to the section in this manual titled "Setting the DPOF" for further details. ) · If there is no image stored in the internal memory or on the SD/SDHC memory card, [No image] message will appear on the LCD monitor screen. · You cannot enter the Playback mode from the Setup mode. EN-35 Magnifying Images While reviewing your images, you may enlarge a selected portion of an image. The zoom factor displayed on the screen shows the current magnification ratio. To view different portions of the images, press the four-way controller ( adjust the display area. 1. 5X ) to · The magnification factors range from 1. 5X to 4X (within 6 stages: 1. 5X, 2. 0X, 2. 5X, 3. 0X, 3. 5X and 4. 0X). EN-36 Thumbnail Display This function allows you to view 9 thumbnail images on the LCD monitor screen simultaneously so you may search for a particular image. (Refer to the section in this manual titled "Protecting Images/Movie Clips" for further details. ) 3. Use the four-way controller ( ) to move the cursor to select the image to be displayed at regular size. Press the or / button to display the selected image on full screen. EN-37 Slideshow Display The slideshow function enables you to play your images back automatically in sequential order. This is very useful and entertaining feature for reviewing recorded images and for presentations. [. . . ] * Transfer the desired files to your computer and then delete unnecessary files, or use a different memory card. Camera suddenly powers down. Flash does not fire. * Flash off is selected in flash * Select a different flash mode. * Insert SD/SDHC memory card with available space or delete unwanted images. Continuous shooting is not possible. Cannot transfer * USB cable is not connected * Check all connections. * Turn on the camera. EN-61 POSSIBLE NUMBER OF RECORDABLE IMAGES The frame counter indicates the approximate number of images that can be stored on the internal memory and the SD/SDHC memory card. [. . . ]