User manual SANYO VPC-S1070

[. . . ] INSTRUCTION MANUAL Digital Camera 10 Mega Pixels VPC-S1070 Preface i About this Manual This manual is designed to assist you in using your new digital camera. All information presented is as accurate as possible but is subject to change without notice. Copyright This manual contains proprietary information protected by copyright. No part of this manual may be reproduced by any mechanical, electronic or other means, in any form, without prior written permission of the manufacturer. © Copyright 2008 Federal Communications Commission (FCC) Compliance This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. [. . . ] Close the battery compartment. To remove the SD/MMC card, gently push the card until it pops out. Pull out the card carefully. Note: Please don't take in and out the SD card while camera is processing. It will make unexpected error or image damaged. Turning On Press and hold the Power button to turn on the camera. To turn off the camera, press the Power button again. Inserting an SD/MMC Memory Card English Inserting an SD/MMC Memory Card 16 Camera Setup First Time Use Press the Power button as described in "Turning On" on page 15, a welcome screen displays momentarily on the LCD screen. English If the camera is turned on for the first time, the Language menu pops up automatically after powering on the camera. Press the OK button and select the desired language by Up/Down navigation buttons, then press the OK button to confirm. ENGLISH DEUTSCH FRANçAIS ITALIANO LANGUAGE After the desired language is selected, the Date and Time menu pops up. Press the OK button to confirm. Press OK when done (Year) 2008 / 01 / 01 12 : 00 DATE & TIME Note: If the Date and Time is reset (when running out the battery and not in use for a long period), the Date and Time setup screen displays automatically. First Time Use Getting Started 17 Now that you are familiar with the layout of your camera, you are ready to start taking photos and movies. Taking your First Photo Taking a photo with the camera is very simple. Turn the camera on and press the SCENE button to access the Auto mode. Frame the shot on the LCD screen and press the Shutter button halfway. When a camera steady warning icon appears, hold the camera as still as possible, as a longer exposure time (more than 1/30 second) is required. Anti-Shake Function This function is available in Auto capture mode. Press the OK button to enable the AntiShake function, and press again to disable it. An Anti-Shake icon displays on the LCD screen when the function is activated. Using Macro Mode Macro mode is designed for close-up photography and can capture all detail even when your subject is very close to the camera. The Macro icon displays on the LCD screen. Setting the Flash Mode You can choose from four flash modes to suit various lighting conditions. Press the Up/Flash/Delete navigation button to scroll through the four modes on the LCD screen. The flash setting remains the same for subsequent photos until you change it as described above. Fill flash: The flash always fires. Taking your First Photo English Getting Started 18 Getting Started Anti Red-eye: The flash fires twice so as to reduce the red-eye effect. English Using the Zoom in/out Function The camera comes equipped with 3x optical zoom and 5x digital zoom that allows you to zoom in on your subject. to zoom out from your subject. Using the Self-timer and Burst Photography The camera comes equipped with a self-timer which allows you to take photos after a pre-defined delay. The burst photography feature allows you to take multiple consecutive photos by pressing and holding the Shutter button. The multi-burst photography feature allows you to take multiple (16) consecutive VGA photos by pressing the Shutter button once. Press the Right/Self-timer/Burst mode navigation button to cycle through the self-timer( or ) and burst photography options ( or ) on the LCD screen. In self-timer mode, the icon will flash until the time expires and the photo is taken. If you want to use these functions for the next photo, press the Right/Self-timer/Burst mode navigation button again to activate the function. Note: : Burst Mode Take photos until all free memory space is used. : Multi-Burst Mode 16 photos continuously by 1 press of the Shutter button. Taking your First Photo Getting Started 19 Using the AEB (Auto Exposure Bracketing) Function When using the AEB (Auto Exposure Bracketing) function, the camera automatically takes 3 consecutive photos with different exposures by pressing the Shutter button once. [. . . ] Press the OK button to enter selection function, select YES to proceed with the Reset or EXIT (default) to cancel. Reset to camera default setting?YES EXIT RESET The Setup Menu English 44 Camera Settings Voice Memo English The Voice Memo setting allows you to record a voice memo when a photo is taken. Select ON to enable the Voice Memo function or OFF (default) to disable it. ON OFF VOICE MEMO About The About screen allows you to check the current firmware version of the camera. MENU FW VERSION : 1. 0000 ABOUT PictBridge Print (PTP) The PTP function allows you to print images captured by the camera directly without connecting the camera to a PC. If the camera is not connected to a PTP compliant printer, an error message displays on the LCD screen. To enable PTP function, see "USB Mode" on page 41 for detailed information. [. . . ]