User manual SANYO VPC-E1090

[. . . ] INSTRUCTION MANUAL Digital Camera 10 Mega Pixels VPC-E1090 Preface i About this Manual This manual is designed to assist you in using your new digital camera. All information presented is as accurate as possible but is subject to change without notice. Copyright This manual contains proprietary information protected by copyright. No part of this manual may be reproduced by any mechanical, electronic or other means, in any form, without prior written permission of the manufacturer. © Copyright 2009 Federal Communications Commission (FCC) Compliance This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. [. . . ] Turn the camera on and press the SCENE button to access the Auto mode. Frame the shot on the LCD screen and press the SHUTTER button halfway. When a camera steady warning icon appears, hold the camera as still as possible, as a longer exposure time (more than 1/30 second) is required. Anti-Shake Function This function is available in Auto capture mode. Press the OK button to enable the Anti-Shake function, and press again to disable it. An Anti-Shake icon displays on the LCD screen when the function is activated. Taking your First Photo English Getting Started 20 Getting Started Using Macro Mode English Macro mode is designed for close-up photography and can capture all detail even when your subject is very close to the camera. Macro mode range: 10-70cm(Wide) 35-70cm(Tele) Setting the Flash Mode You can choose from 4 flash modes to suit various lighting conditions. Press the UP/FLASH /DELETE navigation button to scroll through the four modes on the LCD screen. The flash setting remains the same for subsequent photos until you change it as described above. Anti Red-eye: The flash fires twice so as to reduce the red-eye effect. Using the Zoom in/out Function The camera comes equipped with 3x optical zoom and 5x digital zoom that allows you to zoom in on your subject. to zoom out from your subject. Using the Self-timer and Burst Photography The camera comes equipped with a self-timer which allows you to take photos after a predefined delay. The burst photography feature allows you to take multiple consecutive photos by pressing and holding the SHUTTER button. The multi-burst photography feature allows you to take multiple (16) consecutive VGA photos by pressing the SHUTTER button once. Taking your First Photo Getting Started 21 To set the self-timer/burst mode: 1. Press the RIGHT/SELF-TIMER /BURST MODE navigation button to cycle through the self-timer( or ) and burst photography options ( or ) on the LCD screen. In self-timer mode, the icon will flash until the time expires and the photo is taken. If you want to use these functions for the next photo, press the RIGHT/SELF-TIMER button again to activate the function. Note: : Burst Mode - Take photos until shutter is released or memory is full. : Multi-Burst Mode - 16 photos continuously by 1 press of the SHUTTER button. /BURST MODE navigation Using the AEB (Auto Exposure Bracketing) Function When using the AEB (Auto Exposure Bracketing) function, the camera auto-matically takes 3 consecutive photos with different exposures by pressing the SHUTTER button once. For example, when the current EV compensation value is +1. 0 EV and the AEB bracket interval value is set to ±0. 3, the camera takes shots of the same scene with 3 varying levels of exposure: +0. 7 EV, +1. 0 EV and +1. 3 EV. Press the LEFT/RIGHT navigation buttons to select AEB AEB OFF setting and press the OK button. Press the UP/DOWN navigation buttons to select from the EXIT available options: · AEB: Select to enable (ON) or disable (OFF) the AEB AEB function. · BRACKET: Select to set the bracket interval value ranging from ±0. 3 to ±2. 0 EV in 0. 3 or 0. 4 EV increments. · EXIT: Select to apply new settings to the camera and return to the setup menu. Note: 1. Flash, Burst, and M-Burst modes are not allowed when the AEB function is enabled. [. . . ] This means all modifications you have made to the camera settings will be cleared. Select EXIT(default) to cancel or YES to proceed with the Reset and press the OK button to confirm. Reset to camera default setting?YES EXIT RESET Voice Memo The Voice Memo setting allows you to record a voice memo when a photo is taken. Select ON to enable the Voice Memo function or OFF (default) to disable it. ON OFF VOICE MEMO The Setup Menu Camera Settings 49 About The About screen allows you to check the current firmware version of the camera. MENU FW VERSION : 1. 0000 ABOUT PictBridge Print (PTP) The PTP function allows you to print images captured by the camera directly without connecting the camera to a PC. [. . . ]