User manual SANYO VCP-HD 1A EX

[. . . ] If the problem still persists, contact the sales dealer where you purchased the projector or the service center. SAFETY PRECAUTIONS WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. Be especially careful that children do not stare directly into the beam. G Do not use projectors with whiteboards that produce a very bright glare or 'hot spot'. G Take appropriate space on the top, sides and rear of the projector cabinet for allowing air circulation and cooling the projector. [. . . ] Move a pointer to either RGB (Digital) or RGB (Analog) and then press SELECT button. When analog signal is connected to DVI terminal, select Analog. Computer 2 INPUT Menu icon Move a pointer (red arrow) to Computer 2 and press SELECT button. RGB (Digital) RGB (Analog) Source Select Menu Move a pointer to RGB (Digital) or RGB (Analog) and press SELECT button. 22 COMPUTER INPUT SELECTING COMPUTER SYSTEM This projector automatically tunes to most different types of computers based on VGA, SVGA, XGA or SXGA (refer to "COMPATIBLE COMPUTER SPECIFICATIONS" on page 24). When selecting Computer, this projector automatically tunes to incoming signal and projects proper image without any special setting. (Some computers need setting manually. ) Note : Projector may display one of the following messages. Auto When projector cannot recognize connected signal as PC system provided in this projector, Auto PC Adjustment function operates to adjust projector and the message "Auto" is displayed on SYSTEM Menu icon. (Refer to P25. ) When image is not provided properly, manual adjustment is required. Make sure the connection of computer and a projector is set correctly. (Refer to TROUBLESHOOTING on page 42. ) PC SYSTEM MENU SYSTEM Menu icon Displays system being selected. ­­­­ D-VGA, D-SVGA or D-XGA When digital computer signal is received on DVI terminal, above message is displayed on PC SYSTEM Menu icon. SELECT COMPUTER SYSTEM MANUALLY This projector automatically selects PC system among those provided in this projector and PC system can be also selected manually. PC SYSTEM MENU 1 2 Press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT buttons to move a red frame pointer to PC SYSTEM Menu icon. Press POINT DOWN button to move a red arrow pointer to the system that you want to set, and then press SELECT button. SYSTEM Menu icon Displays system being selected. (P26, 27) 23 COMPUTER INPUT COMPATIBLE COMPUTER SPECIFICATIONS Basically this projector can accept the signal from all computers with the V, H-Frequency below mentioned and less than 140 MHz of Dot Clock. ON-SCREEN DISPLAY RESOLUTION 640 x 480 720 x 400 640 x 400 640 x 480 640 x 480 640 x 480 640 x 480 640 x 480 640 x 480 ­­­­­­­­ ­­­­­­­­ VGA 1 VGA 2 VGA 3 VGA 4 VGA 5 VGA 6 VGA 7 MAC LC13 MAC 13 RGB RGB SVGA 1 SVGA 2 SVGA 3 SVGA 4 SVGA 5 SVGA 6 SVGA 7 SVGA 8 SVGA 9 SVGA 10 SVGA 11 MAC 16 XGA 1 XGA 2 XGA 3 XGA 4 XGA 5 XGA 6 XGA 7 XGA 8 XGA 9 XGA 10 800 x 600 800 x 600 800 x 600 800 x 600 800 x 600 800 x 600 800 x 600 800 x 600 800 x 600 800 x 600 800 x 600 832 x 624 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 H-Freq. Press POINT LEFT/RIGHT button to adjust value. (From 0 to 31. ) Total dots The number of total dots in one horizontal period. Press POINT LEFT/RIGHT button(s) and adjust number to match your PC image. Current mode Press SELECT button to show the information of computer selected. Press SELECT button at this icon to adjust "Clamp, " "Display area (H/V)" or set "Full screen. " Selected Mode Shows status (Stored / Free) of the selected Mode. Press SELECT button at Current mode icon to show the information of computer connected. 26 COMPUTER INPUT Display area Selects area displayed with this projector. Display area H Adjustment of horizontal area displayed with this projector. Press POINT LEFT/RIGHT button(s) to decrease/increase value and then press SELECT button. Display area V Adjustment of vertical area displayed with this projector. Press POINT LEFT/RIGHT button(s) to decrease/increase value and then press SELECT button. Full screen Press POINT LEFT/RIGHT button(s) to switch Full screen function to "On" or "Off. " Set "On" to resize the image with 4 x 3 aspect ratio to fit the screen. NOTE : Fine sync, Display area, Display area H, Display area V and Full screen cannot be adjusted when "RGB", "1035i (HDTV)", "1080i50(HDTV)" or "1080i60 (HDTV)" is selected on PC SYSTEM Menu (P23). Press SELECT button at Display area icon and Display area dialog box appears. Display area Press POINT LEFT /RIGHT button(s) to adjust value and then press SELECT button. To store adjustment data. This Mode has parameters being stored. 3 Store To store adjustment parameters, move a red frame pointer to Store icon and then press SELECT button. Move a red arrow pointer to any of Mode 1 to 5 that you want to store to and then press SELECT button. [. . . ] G Press MUTE button. No sound. 42 APPENDIX Problem: Remote Control Unit does not work. G G G G Try these Solution Check the batteries. Check ALL-OFF switch on Remote Control Unit is set to "ON. ". Make sure nothing is between Infrared Remote Receiver and Remote Control Unit. Make sure you are not too far from a projector when using Remote Control Unit. [. . . ]