User manual SANYO VCC-6594E

[. . . ] This warranty does not apply to repairs or replacements necessitated by any cause beyond the control of SFC including, but not limited to, any malfunction, defect or failure caused by or resulting from unauthorized service or parts, improper maintenance, operation contrary to furnished instructions, shipping or transit accidents, modification or repair by the user, abuse, misuse, neglect, accident, incorrect power line voltage, fire, flood or other Acts of God, or normal wear and tear. The foregoing is in lieu of all other expressed warranties and SFC does not assume or authorize any party to assume for it any other obligation or liability. SFC DISCLAIMS ALL OTHER WARRANTIES EXPRESS OR IMPLIED, WITH REGARD TO THIS PRODUCT (INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS). IN NO EVENT SHALL SFC BE LIABLE FOR ANY SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING FROM THE OWNERSHIP OR USE OF THIS PRODUCT OR FOR ANY DELAY IN THE PERFORMANCE OF ITS OBLIGATIONS UNDER THIS WARRANTY DUE TO CAUSES BEYOND ITS CONTROL. [. . . ] Make sure that no plastic or rubber material comes in contact with the cabinet for a long period of time, as that may cause damage or paint peeling. English 3 L53H4/US (VCC-6594) GB 2001, 11, 9 PARTS NAMES 1 Video output connector (VIDEO OUT: BNC type) Connect this connector to a device such as a VCR or monitor with a VIDEO IN connector. 1 4 3 2 Line phase adjustment volume (LINE PHASE) When using two cameras or more, the image on the monitor may roll vertically when switching sources. This rolling can be minimized by turning this volume. 2 3 Power input terminal 24 V AC input terminal (AC 24 V, GND) 4 Power indicator (POWER) Comes on when the power to the camera is on. 4 English L53H4/US (VCC-6594) GB 2001, 11, 9 PARTS NAMES 5 Lens mount cap The cap is installed to protect the lens mount section. Remove the lens mount cap before installing a lens (sold separately). 6 Flange-back adjustment screw (FLANGE BACK ADJ. ) 5 8 7 6 7 Flange-back lock screw (FLANGE BACK LOCK) 8 Camera installation bracket The bracket can be fixed at the top or bottom of the camera. When fixing the bracket, be sure to use the longer screws and install the shorter screws on the opposite side to seal the openings. 1 2 32 CAUTION: When installing the camera support, select a location that can support the total weight of the camera and accessories. 1 1 Shorter screws: M3 x 4 2 Longer screws: M3 x 6 3 Camera mounting screw hole: 1/4"-20 UNC English 5 L53H4/US (VCC-6594) GB 2001, 11, 9 PARTS NAMES 9 Lens iris output connector (LENS) F 9 This 4-pin connector is used to send the DC control signal and power supply to an auto-iris type lens. F Camera setup section (under the cover) These settings are for when using a 1/3 inch CS mount DC (without EE internal amplifier) type lens. However, if due to installation conditions or environment the settings may need to be modified for best results (see "SETTINGS"). To access the controls, remove the cover fixing screw, then remove the cover. Connect the lens plug to the lens iris output connector (LENS) on the side of the camera. When using lenses from other makers, the plug shape may not correspond to the terminal on the camera. In such a case, remove the original plug and using a soldering iron, connect the supplied lens iris plug according to the diagram. (Refer to page 9. ) 3 2 CS mount type lens 3 8 English L53H4/US (VCC-6594) GB 2001, 11, 9 MOUNTING THE LENS Rewiring the lens cable in the lens iris plug 1 1 2 2 Prepare the lens cable. Solder the cable to the pins following the correct pin layout (refer to the table and illustrations), then close the plug cover. Pin layout 2 4 1 3 2 4 1 3 1 2 3 4 DC type lenses Brake coil (­) Brake coil (+) Drive coil (+) Drive coil (­) VIDEO type lenses +12 V DC (50 mA max. ) Not used Video output (1. 0 Vp-p, high impedance) Ground (for video signal and DC power) Flange-back adjustment 2, 3 If the pick-up surface is not correctly positioned with relation to the lens focal point, the picture will be out of focus (in particular when using auto-iris power zoom lenses, sold separately). If that is the case, adjust the flange-back position as described below. 3 ADJ. 1 LOCK 4 1 2 3 4 Using a + screwdriver, loosen the FLANGE BACK LOCK screw (M2:+). Set the zoom lens to the maximum telephoto position, set the focus using the focus ring on the lens. Set the zoom lens to the maximum wide angle position, set the focus using the FLANGE BACK ADJ. Repeat steps 2 and 3, until the image stays in focus when changing from a telephoto shot to a wide angle shot. When the setting is complete, tighten the FLANGE BACK LOCK screw. English 9 L53H4/US (VCC-6594) GB 2001, 11, 9 CONNECTIONS 1 (A) 3 AC 24 V connection Push to insert the cable AC 24 V 2 (Video signal connections) : VIDEO IN : VIDEO OUT ~~ GND Basic connection for monitoring or recording The peripheral devices (VCR, monitor, lens, etc. ), AC adaptor and cables are sold separately. Coaxial cable type and maximum length 1 2 3 Make the video signal connection between the camera and the monitor or time lapse VCR. Connect an AC 24 V power source to the AC 24 V input terminal on the back of the camera. Adjust the picture on the monitor using the Brightness and Contrast controls etc. · Cable type RG-59U (3C-2V), 250 m maximum. · Cable type RG-11U (7C-2V), 600 m maximum. CAUTION: · The RG-59U type cable should not be run through electrical conduits or through the air. · Using CCTV/Video-grade coaxial cable. 10 English L53H4/US (VCC-6594) GB 2001, 11, 9 SETTINGS The illustration shows the factory default settings for the switches in the camera setup section. The camera settings are described on the assumption that a DC type auto iris lens is being used. If you are using a VIDEO type auto iris lens, be sure to read the Note which is given. 6 R VR302 9 B VR303 Control name Position 1/60 sec. NORM NORM OFF OFF ATW INT DC adjustable 1 High speed electronic shutter (ES)/ VR301 Electronic iris (EI) setting ON 1 2 3 4 5 6 7 8 9 10 DC VIDEO 2 Auto gain control setting (HI/NORM) A. [. . . ] If it still does not perform correctly, please consult your dealer or a Sanyo Authorized Service Centre. No picture on the monitor screen Is the power turned on to all connected devices?· Is the iris control correctly set? · · · · · · · · · The picture is not clear Is the monitor correctly adjusted?If there is dust or finger prints on the lens, the image quality will deteriorate. [. . . ]