User manual SANYO VCC-5974

[. . . ] INSTRUCTION MANUAL COLOR CCD Camera VCC-5974 About this manual · Before installing and using the camera, please read this manual carefully. Be sure to keep it handy for later reference. SANYO INDUSTRIAL VIDEO COLOR VIDEO CAMERA LIMITED WARRANTY OBLIGATIONS In order to obtain warranty service, the product must be delivered to and picked up from an Authorized Sanyo Service Center at the user's expense, unless specifically stated otherwise in this warranty. The names and addresses of Authorized Sanyo Service Centers may be obtained by writing to SFS Corporation, SFC's warranty administrator, at any of the addresses listed below, or by calling (toll-free) 1-800-421-5013. New Jersey Office 210 Riser Road Little Ferry, NJ 07643 201-641-3000 California Office 1200 W. [. . . ] when the subject will be moving in the screen area) and stored under one of the two manual settings. OFF: Fixed backlight compensation Notes: · The backlight compensation will operate when using an auto-iris lens (DC or VIDEO type). · If in the "MENU FOR ADJUSTMENT", AGC is set to OFF, the backlight compensation will not operate. ON OFF W0=1 W2=10 W4=15 W3=10 W1=5 Fig. 2 WINDOW WEIGHTING W0 W1 W2 W3 W4(FIX) PRESET MENU END 1 1 3 3 15 OFF END Fig. 3 Iris level setting The iris is set using the IRIS AI (Auto-Iris)/EI (Electronic Iris) switch (10) in the camera setup section. When using a DC type auto-iris lens, the iris level settings can then be entered in the adjustment sub-menu (see page 17). Note: If the AGC switch is set to OFF, setting the IRIS switch to EI will not set the electronic iris mode. AI EI 12 English USING THE ON-SCREEN MENUS (Menu 1) MENU FOR ADJUSTMENT SYNC IRIS BLC WHITE BALANCE AGC SHUTTER WRITE PROTECT INT AI ON ATW ON 60 ON END (Menu 2) MENU FOR ADJUSTMENT CAMERA ID APERTURE OFF 2 3 4 8 7 WRITE PROTECT ON END 5 NEXT PAGE 6 PREVIOUS PAGE 1 2 To display the menu Press the SET button for about 3 seconds. To switch between menus and selection When the setting of a switch in the camera setup section is changed, the corresponding sub-menu is displayed. To adjust the values or settings, press the CURSOR (d or c) button to select the desired value or setting, then press the SET button. OFF: Press the CURSOR (d or c) button to select OFF, then press the SET button. The write protection is cancelled and the initial values can then be changed. To exit the menu Press the CURSOR (j or l) button to select END (get it flashing), then press the SET button. To switch to the second page of the "MENU FOR ADJUSTMENT" Press the CURSOR (j or l) button to select NEXT PAGE (get it flashing), then press the SET button. To switch back to the first page of the "MENU FOR ADJUSTMENT" Press the CURSOR (j or l) button to select PREVIOUS PAGE (get it flashing), then press the SET button. Aperture display (APERTURE) (See page 25). SET INT CURSOR SET 3 CURSOR CURSOR SET 4 5 6 7 8 CURSOR SET (or j) English 13 ADJUSTMENTS To enter settings or adjustments for the camera it must be connected to a monitor. Concerning the WRITE PROTECT function In order to protect the settings and adjustments the WRITE PROTECT function is set to ON. If it is necessary to enter new settings or adjustments, press the CURSOR (j or l) button to select the WRITE PROTECT function setting, then press the CURSOR (d or c) button to select OFF, then press the SET button. CURSOR CURSOR SET (Menu 1) MENU FOR ADJUSTMENT SYNC IRIS BLC WHITE BALANCE AGC SHUTTER WRITE PROTECT NEXT PAGE INT AI ON ATW ON 60 OFF END CONTENTS OF ADJUSTMENTS 1. V sync phase adjustment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 1-2. VBS phase adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 2. Auto-iris level adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 3. Setting the light measuring area characteristics (size, position and distribution) for the MANUAL 1 setting. . . . . PRESET MODE 2 (indoors, fluorescent lighting) setting adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Example: To enter the camera ID S123AB Press the CURSOR buttons to select the desired alphanumeric character or symbol (i. e. Repeat the same method to enter the desired camera ID (maximum of 6 characters or symbols). CAMERA ID SETTING CAMERA ID IS ?????? CAMERA ID SETTING ABCDEFGHIJKLM NOPQRSTUVWXYZ 0123456789:-p MENU CAMERA ID IS ?????? 3 4 CAMERA ID SETTING ABCDEFGHIJKLM NOPQRSTUVWXYZ 0123456789:-p MENU CAMERA ID IS S123AB Note: The symbol c indicates a blank space. When entered in a camera ID, it will be displayed as a blank space. 5 6 7 When finished entering the camera ID. Press the CURSOR (d or c) button to select MENU (get it flashing), then press the SET button to return to the "MENU FOR ADJUSTMENT" display. [. . . ]