User manual SANYO VCC-4344

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual SANYO VCC-4344. We hope that this SANYO VCC-4344 user guide will be useful to you.


SANYO VCC-4344 : Download the complete user guide (370 Ko)

Manual abstract: user guide SANYO VCC-4344

Detailed instructions for use are in the User's Guide.

[. . . ] If used with a foreign object inside, it could cause fire, short-circuits or damage. If water or liquid gets inside the camera, disconnect the power cord immediately, and consult your dealer or a Sanyo Authorized Service Center. Be careful to protect the camera from rain, sea water, etc. Cleaning Dirt can be removed from the cabinet by wiping it with a soft cloth. To remove stains, use a soft cloth moistened with a soft detergent solution and wrung dry, then dry by wiping with a soft dry cloth. [. . . ] VIDEO OUT (video output terminal: BNC connector) Connects to the VIDEO IN (video input) terminal on the VCR or monitor. CONTROL (Manual color/black and white setting terminal) G (ground) terminal C (color) terminal B (black and white) terminal LINE PHASE (Line phase adjustment volume) When using two cameras or more, the image on the monitor may roll vertically when switching sources. GND, AC24V, DC12V (ground terminal, 24V AC or 12V DC input terminal) Camera adjustment/setting panel Contains camera adjustment dials and setting switches. LENS (lens iris output terminal) Used to connect the lens plug when the lens is attached. Brake coil (-) Brake coil (+) Drive coil (+) Drive coil (-) When installing the camera support, select a location that can support the total weight of the camera and accessories. Attaching the lens Use a DC type auto-iris lens (sold separately). Is the lens in focus?Gently wipe any dirt or fingerprints off the lens with a soft cloth or lens cleaning paper and cleaning fluid (commercially available). Is the monitor adjusted correctly? Do not use a lens if length "L" is more than 5 mm. When attaching a C mount lens, attach the lens to the camera after inserting the C mount ring (option). SERVICE L 1 Remove the lens mount cap from the camera. 2 1 CS mount type lens 2 Install the auto-iris lens. 3 Connect the lens plug to 3 the lens iris output connector (LENS) on the side of the camera. The camera is a precision instrument. If the camera requires service, never try to repair it yourself or open the casing. For servicing, maintenance, or repairs, contact your place of purchase or a Sanyo Authorized Service Center. CONNECTIONS Connections Monitor 24 V AC connection AC24V GND White balance (color compensation) 5 5 10 695 The electronic iris is suitable for normal indoor use. When switch 1 (IRIS) is set to the up (EI) position, do not use an auto-iris lens. In such a case, change to incandescent lighting or set switch 1 (IRIS) to the down (AI) position and use an auto-iris lens. When shooting bright subjects, pay attention to the light angle in order to avoid or minimize the smear effect. If conditions are outside the electronic iris operation range or more than the maximum illumination, the CCD will be saturated. In that case, use the auto iris lens. MANU Lets you fine-tune the white balance manually. WB ATW · R (Red) dial 9 : Turn clockwise to augment screen red. · B (Blue) dial 10 : Turn clockwise to augment screen blue. 12 V DC connection Compensation is performed automatically. 3 AC24V GND 1 3 DC12V DC12V 2 2 Vertical sync disturbance may occur when a selector is used to switch between multiple cameras connected to one monitor. To prevent vertical sync disturbance, set to "LL. " LL (external sync) INT (internal sync) Adjust PHASE dial to eliminate sync disturbance. Internal Sync Sync setting 7 GCB Aperture (outline compensation) 2 If object outlines appear too strongly, set to "NORM". Normal setting LL (Line-Lock): Synchronizes the unit with power frequency. Flange-back adjustment Camera adjustment Gain control (AGC) 3 VR302 VR303 VR301 2 Digital video recorder or time-lapse VCR : VIDEO IN : VIDEO OUT Flange-back lock screw For adjusting the sensitivity of the camera. Use this setting for shooting in dark environments. HI Increased sensitivity allows shots to be taken in dark environments. [. . . ] SFC DISCLAIMS ALL OTHER WARRANTIES EXPRESS OR IMPLIED, WITH REGARD TO THIS PRODUCT (INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS). IN NO EVENT SHALL SFC BE LIABLE FOR ANY SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING FROM THE OWNERSHIP OR USE OF THIS PRODUCT OR FOR ANY DELAY IN THE PERFORMANCE OF ITS OBLIGATIONS UNDER THIS WARRANTY DUE TO CAUSES BEYOND ITS CONTROL. SFC'S LIABILITY FOR ANY AND ALL LOSSES AND DAMAGES RESULTING FROM ANY CAUSE WHATSOEVER, ARISING OUT OF OR IN CONNECTION WITH THE SALE, USE OR OWNERSHIP OF THIS PRODUCT INCLUDING WARRANTOR'S NEGLIGENCE, ALLEGED DAMAGED OR DEFECTIIVE GOODS, WHETHER SUCH DEFECTS ARE DISCOVERABLE OR LATENT, SHALL IN NO EVENT EXCEED THE PURCHASE PRICE OF THE PRODUCT. 4 Repeat steps 2 and 3, until the image stays in focus when changing from a telephoto shot to a wide angle shot. When the setting is complete, tighten the flange-back lock screw. When connecting the power cable to the camera, check that the polarity is correct. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE SANYO VCC-4344




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual SANYO VCC-4344 will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.