User manual SANYO VCC-4324

[. . . ] This warranty does not apply to repairs or replacements necessitated by any cause beyond the control of SFC including, but not limited to, any malfunction, defect or failure caused by or resulting from unauthorized service or parts, improper maintenance, operation contrary to furnished instructions, shipping or transit accidents, modification or repair by the user, abuse, misuse, neglect, accident, incorrect power line voltage, fire, flood or other Acts of God, or normal wear and tear. The foregoing is in lieu of all other expressed warranties and SFC does not assume or authorize any party to assume for it any other obligation or liability. THE DURATION OF ANY WARRANTIES WHICH MAY BE IMPLIED BY LAW (INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS) IS LIMITED TO THE TERM OF THIS WARRANTY. IN NO EVENT SHALL SFC BE LIABLE FOR SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING FROM OWNERSHIP OR USE OF THIS PRODUCT, OR FOR ANY DELAY IN THE PERFORMANCE OF ITS OBLIGATIONS UNDER THIS WARRANTY DUE TO CAUSES BEYOND ITS CONTROL. [. . . ] Protect from humidity and dust To prevent damages to the camera, do not install it where there is greasy smoke or steam, where the dampness may get too high, or where there is a lot of dust. Protect from high temperatures Do not install close to stoves, or other heat generating devices, such as spotlights, etc. , or where it could be subject to direct sunlight, as that could cause deformation, discoloration or other damages. Be careful when installing close to the ceiling, in a kitchen or boiler room, as the temperature may raise to high levels. Install where the temperature range will stay between ­10°C and 50°C. (no condensation) Cleaning · Dirt can be removed from the cabinet by wiping it with a soft cloth. To remove stains, wipe with a soft cloth moistened with a soft detergent solution and wrung dry, then wipe dry with dry soft cloth. · Do not use benzine, thinner or other chemical product on the cabinet, as that may cause deformation and paint peeling. Before using a chemical cloth, make sure to read all accompanying instructions. Make sure that no plastic or rubber material comes in contact with the cabinet for a long period of time, as that may cause damage or paint peeling. English 3 PARTS NAMES 1 1 3 1 Lens iris output connector (4 pin) This 4-pin connector is used to send the DC control signal and power supply to an auto-iris type lens. 2 Flange-back adjustment lever (See page 7) 2 4 2 3 Flange-back lock screw 4 Lens mount cap The cap is installed to protect the lens mount section. Remove the lens mount cap before installing a lens (sold separately). 3 4 5 5 Camera installation bracket The bracket can be fixed at the top or bottom of the camera. When fixing the bracket, be sure to use the longer screws and install the shorter screws on the opposite side to seal the openings. 1 2 32 CAUTION: When installing the camera support, select a location that can support the total weight of the camera and accessories. 1 1 Shorter screws: M3 x 4 2 Longer screws: M3 x 6 3 Camera mounting screw hole: 1/4"-20 UNC 4 English PARTS NAMES 6 Camera setup section (under the cover) This unit factory settings are as indicated below. These settings are for when using a 1/3 inch CS mount DC (without EE internal amplifier) type lens. However, if due to installation conditions or environment the settings may need to be modified for best results (see "SETTINGS"). To access the controls, remove the cover fixing screw, then remove the cover. Control name Position L INT about center A OFF DC about center 6 ab C-BW de f g WB EI A ON OFF ON VR301 a Color and Black/White level switch (C-BW) b Internal/Line lock switch (SYNC) c Red and Blue color adjustment volume (R, B) d e f g White balance switch (WB) Electronic iris (EI)/Backlight compensation (BLC) switch Auto-iris lens switch (A. I. LENS) Lens iris level volume (LEVEL) L-L H L INT SYNC R VR303 VR302 LEVEL L H M B BLC DC VIDEO A. LENS c Notes: · The EI/BLC switch cannot be used simultaneously. · When using a 1/2 or 2/3 inch C mount VIDEO (with EE internal amplifier) auto-iris type lens, set the A. I. LENS switch to the DC type) a CS mount type lens without the need of an adaptor. If the lens plug shape or wiring does not correspond, please install the supplied plug as indicated in the pin layout table. 2 (A) (B) Installation of a VIDEO type auto-iris lens (sold separately) A 1/2 or 2/3 inch C mount type lens with EE amplifier circuit that uses the video signal and a DC power source. 1 2 3 3 1 2 4 3 Remove the lens mount cap. Attach the supplied C mount adaptor (A) to the auto-iris lens (B), then install the assembly on the camera. Connect the lens plug to the LENS connector on the side of the camera. [. . . ] · When using infrared lighting, if there is a strong reflection on the subject, the optical filter may switch from black and white to color mdoe, Use only enough infrared lighting so that the mode is not switched. · The focus setting may be different in black and white mode and color mode. Please check the focus setting in both modes. · · · · The picture is not clear Is the monitor correctly adjusted?If there is dust or finger prints on the lens, the image quality will deteriorate. [. . . ]