User manual SANYO VCC-3924

[. . . ] Changes or modifications not expressly approved by Sanyo may void the user's authority to operate this camera. 2 English PRECAUTIONS s In case of problem Do not use the camera if smoke or a strange odour comes from the unit, or if it seems not to function correctly. Disconnect the power cord immediately, and consult your dealer (or a Sanyo Authorized Service Centre). s Do not open or modify Do not open the cabinet, as it may be dangerous and cause damage to the unit. For internal settings and repairs, consult your dealer (or a Sanyo Authorized Service Centre). [. . . ] Install where the temperature range will stay between ­10°C and 50°C. (no condensation) s Cleaning · Dirt can be removed from the cabinet by wiping it with a soft cloth. To remove stains, wipe with a soft cloth moistened with a soft detergent solution and wrung dry, then wipe dry with dry soft cloth. · Do not use benzine, thinner or other chemical product on the cabinet, as that may cause deformation and paint peeling. Before using a chemical cloth, make sure to read all accompanying instructions. Make sure that no plastic or rubber material comes in contact with the cabinet for a long period of time, as that may cause damage or paint peeling. English 3 PARTS NAMES 2 1 Flange-back lock screw (LOCK) 2 Flange-back adjustment dial 3 Lens mount cap The cap is installed to protect the lens mount section. 4 Camera installation bracket The bracket can be fixed at the top or bottom of the camera. When fixing the bracket, be sure to use the longer screws and install the shorter screws on the opposite side to seal the openings. 1 3 4 CAUTION: When installing the camera support, select a location that can support the total weight of the camera and accessories. 1 Shorter screws: M3 x 4 2 Longer screws: M3 x 6 3 Camera mounting screw hole: 1/4"-20 UNC 4 English PARTS NAMES 9 5 6 7 8 9 Camera setup section White balance adjustment volume (WB R or B) Line phase adjustment volume (PHASE) Lens iris adjustment volume (LEVEL) Lens iris output connector (LENS) 5 6 7 8 This 4-pin connector is used to send the DC control signal and power supply to an auto-iris type lens. F Video output connector (VIDEO OUT: BNC type) Connect this connector to a device such as a VCR or monitor with a VIDEO IN connector. G 24 V AC or 12 V DC input terminal (AC24V, DC12V, GND) H Power indicator (POWER) Comes on when the power to the camera is on. F G H s Power supply connections Use a 3 wire grounded cable (18 AWG or more), and connect as shown by the illustration. CAUTION: · To prevent camera and/or AC adaptor failure, pay close attention to polarity when making the connections. · To prevent fire hazard any UL listed wire rated VW-1, should be used for the 24 V AC cable input terminal. English 5 MOUNTING THE LENS Please use a DC type auto-iris lens (sold separately). 1 Check the lens mount Do not use a lens if the length "L" is more than 5 mm. In such a case, change to incandescent lighting or set the switch 1 to the down (AI) position and use an auto-iris lens. · When shooting bright subjects, pay attention to the light angle in order to avoid or minimize the smear phenomenon effect. HI NORM 10 English SETTINGS s Backlight compensation setting 3 4 This camera has two different backlight correction functions: multi-spot photometry (MULTI) and center focus photometry (CENT). The normal setting (switch 3 and 4) is the down position, but you can change the switch 3 or 4 setting in accordance with the backlight conditions. (MULTI mode: 64 sections) MULTI CENT 3 4 · MULTI mode: Use this position when applying backlight compensation to the whole of the screen. · CENT mode: Use this position when applying backlight compensation to only the central portion of the screen. Note: · When using the backlight compensation function, set the switch 3 or 4 to the up position. When not using the function, set the switch 3 and 4 to the down (OFF) position. · When MULTI mode is set, scenes with no backlighting may appear extremely dark and the object may appear overexposed. If this happens, move the switch 4 to the up (CENT) position. (CENT mode) English 11 SETTINGS Normally the switch 5 is set to the down (ATW: auto white balance) position and the white balance is adjusted automatically. If a manual white balance adjustment is necessary, follow the steps below. · Turn R to set the red ratio and/or B to set the blue ratio. s White balance adjustment 5 s Line phase adjustment 6 When using a camera switcher to connect 2 cameras or more to one monitor, there may be a vertical roll of the images when switched. [. . . ] THE ORIGINAL DATED BILL OF SALE, SALES SLIP OR RENTAL AGREEMENT MUST BE SUBMITTED TO THE AUTHORIZED SANYO SERVICE CENTER AT THE TIME WARRANTY SERVICE IS REQUESTED. Subject to the OBLIGATIONS above and EXCLUSIONS below, SANYO Fisher Company warrants this SANYO product against defects in materials and workmanship for the periods specified below. SFC will repair or replace (at its option) the product and any of its parts which fail to conform to this warranty. The warranty period commences on the date the product was first purchased or rented at retail. LABOR 3 YEARS PARTS 3 YEARS IMAGE DEVICE 3 YEARS EXCLUSIONS This warranty does not cover (A) the adjustment of customer-operated controls as explained in the appropriate model's instruction manual, or (B) the repair of any product whose serial number has been altered, defaced or removed. [. . . ]