User manual SANYO VCC-3912

[. . . ] This warranty does not apply to repairs or replacements necessitated by any cause beyond the control of SFC including, but not limited to, any malfunction, defect or failure caused by or resulting from unauthorized service or parts, improper maintenance, operation contrary to furnished instructions, shipping or transit accidents, modification or repair by the user, abuse, misuse, neglect, accident, incorrect power line voltage, fire, flood or other Acts of God, or normal wear and tear. The foregoing is in lieu of all other expressed warranties and SFC does not assume or authorize any party to assume for it any other obligation or liability. THE DURATION OF ANY WARRANTIES WHICH MAY BE IMPLIED BY LAW (INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS) IS LIMITED TO THE TERM OF THIS WARRANTY. IN NO EVENT SHALL SFC BE LIABLE FOR SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING FROM OWNERSHIP OR USE OF THIS PRODUCT, OR FOR ANY DELAY IN THE PERFORMANCE OF ITS OBLIGATIONS UNDER THIS WARRANTY DUE TO CAUSES BEYOND ITS CONTROL. [. . . ] Be careful when installing close to the ceiling, in a kitchen or boiler room, as the temperature may raise to high levels. Install where the temperature range will stay between ­10°C and 50°C. (no condensation) Cleaning · Dirt can be removed from the cabinet by wiping it with a soft cloth. To remove stains, wipe with a soft cloth moistened with a soft detergent solution and wrung dry, then wipe dry with dry soft cloth. · Do not use benzine, thinner or other chemical product on the cabinet, as that may cause deformation and paint peeling. Before using a chemical cloth, make sure to read all accompanying instructions. Make sure that no plastic or rubber material comes in contact with the cabinet for a long period of time, as that may cause damage or paint peeling. 4 English PREPARATION 1 2 32 2 1 B A Camera installation A: Lens mount cap Remove the lens mount cap before installing the lens (sold separately). · Use with this camera a CS mount type auto-iris lens (for 1/3 inch). Auto-iris lenses regulate the amount of light entering the camera according to the brightness of the subject. · C mount auto-iris lenses can also be used with the supplied adaptor (see page 7). R1 R2 CAUTION: · When installing the camera support, select a location that can support the total weight of the camera and accessories. · This installation should be made by a qualified service person and should conform to all local codes. B: Installation bracket The bracket can be fitted at the top or bottom of the camera. To fix the bracket, make sure to use the screws that held the bracket before, and use the other two screws to seal the openings on the opposite side. 1 Opening sealing screws (M3x4) (shorter) 2 Bracket fixing screws (M3x6) (longer) 3 Threaded hole for the support (1/4"­20 UNC) · Mounting at the top (R1) · Mounting at the bottom (R2) English 5 (A) 1 L 4 DC VIDEO 3 2 Installation of a DC type lens (sold separately) 1/3 inch CS mount type (Flange-back: 12. 5 mm) LENS connector layout (A) 1: Brake coil (­) 2: Brake coil (+) 3: Drive coil (+) 4: Drive coil (­) 1 2 Remove the lens mount cap. In such a case, adjust the LEVEL volume on the lens casing to correct. Compatible auto-iris lens · f= 9 mm (Standard angle) · f= 12 mm (Telephoto) · f= 16 mm (More telephoto) English 7 CONNECTIONS 1 4 (A) 2 (Video signal connections) : VIDEO IN : VIDEO OUT Basic connection for monitoring or recording The peripheral devices (VCR, monitor, etc. ) and cables are sold separately. Coaxial cable type and maximum length · Cable type RG-59U, 100 m maximum. · Cable type RG-39U, 200 m maximum. 1 2 3 4 Make the video signal connection between the camera and the monitor or time lapse VCR. Connect DC connecting cord from the AC adaptor to the 12V DC IN terminal on the camera. When the power is connected to the camera, the POWER indicator (A) will light. Adjust the picture on the monitor using the Brightness and Contrast controls. CAUTION: The RG-59U type cable should not be run through electrical conduits or through the air. WARNING: · This AC adaptor is specially conceived for this camera. Never use another type of AC adaptor with this camera, and do not use this AC adaptor to power other types of cameras. · Never try to disassemble or modify the AC adaptor. 8 English CONNECTIONS A B (Video signal connections) : VIDEO IN : VIDEO OUT : CAMERA IN Multiple camera connections The following two connections can be used when using 4 monitoring cameras. [. . . ] B: When using a VIDEO type lens, the LEVEL volume (on the lens) should be adjusted. · · · · · · · · · The picture is not clear Is the monitor correctly adjusted?If there is dust or finger prints on the lens, the image quality will deteriorate. To clean the lens use a soft cloth or a commercially available lens cleaning set. SERVICE This camera is a precision instruments and if treated with care, will provide years of satisfactory performance. [. . . ]