User manual SANYO VCB-3384

[. . . ] Make sure that no plastic or rubber material comes in contact with the cabinet for a long period of time, as that may cause damage or paint peeling. Pour la clientèle canadienne Cet appareil numerique de la Classe B est conforme à la norme NMB-003 du Canada. This installation should be made by a qualified service person and should conform to all local codes. s Do not put objects inside the unit Make sure that no metal objects or flammable substance get inside the camera. If used with a foreign object inside, it could cause a fire, short-circuits or damages. If water or a liquid gets inside the camera, disconnect the power cord immediately, and consult your dealer or a Sanyo Authorized Service Center. [. . . ] Rear view:> 6 LENS (lens iris output terminal) Used to connect the lens plug when the lens is attached. 1Brake coil (­) 3Drive coil (+) 2Brake coil (+) 4Drive coil (­) 7 8 4 5 <Figure 2. Left view:> F 9 s If no image appears · · · · Is the power ON?Rear view:> 7 VIDEO OUT (video output terminal: BNC connector) 6 1 2 3 4 1 Connects to the VIDEO IN (video input) terminal on the peripheral equipment. s If the image is unclear · Is the lens in focus?Gently wipe any dirt or fingerprints off the lens with a soft cloth or lens cleaning paper and cleaning fluid (commercially available). · Is the monitor adjusted correctly? 8 POWER (power indicator) Lights (red) when the camera power is ON. 9 GND, AC24V, DC12V (ground terminal, 24 V AC or 12 V DC input terminal) F VS IN (External sync composite video signal input terminal: BNC connector) <Figure 1. Right view:> 1 Lens cap Protects the lens from damage. SERVICE The camera is a precision instrument. If the camera requires service, never try to repair it yourself or open the casing. For servicing, maintenance, or repairs, contact your place of purchase or a Sanyo Authorized Service Center. Power supply Power consumption Weight Accessories 2 Flange-back adjustment dial Adjusts the flange-back distance when a zoom lens is attached. Appearance and specifications are subject to change without prior notice. 121. 3 109. 5 57 3 Camera adjustment/setting panel Contains camera adjustment dials and setting switches. 0. 5 4 LOCK Locking screw for the flange-back adjustment dial. 9 41. 7 1/4"-20 UNC 14 45 5 Camera attachment bracket Used to attach the camera. CONNECTIONS, SETTINGS Connections Monitor DC12V Figure A 24 V AC connection AC24V GND 12 V DC connection C Camera adjustment/Settings 3 The camera comes pre-adjusted and ready to install at time of factory shipment, but you may want to make adjustments or settings to adapt to the operating conditions or installation environment, if necessary. If you have trouble adjusting the camera, contact your place of purchase or a Sanyo Authorized Service Center. · The settings shown for switches and are the settings at time of factory shipment. (5 = Factory default setting) 5 Lens switching Set this as appropriate for the type of lens you are using. EI VIDEO DC 5 Electronic iris lens Video auto-iris lens (lens with built-in amp circuits) DC-type auto-iris lens (lens without built-in amp circuits, powered by DC power only) 3 2 AC24V GND DC12V 1 2 VIDEO OUT VS IN POWER Figure 1 Figure 2 CAUTION When using a video auto-iris lens · Turn the ALC (light control) dial on the lens barrel fully to AV (average). · If the backlight compensation is not correct, adjust the LEVEL dial on the lens barrel. Camera installation Camera screws (Shorter) Camera adjustment/Settings BLC LL VIDEO ON OFF PHASE LEVEL L H Backlight compensation (BLC) DC q Flange-back adjustment (only when zoom lens is attached) Flange back is the distance between the lens and the camera (CCD). Follow the steps below to adjust the flange back distance, since the image can become out of focus when you are zoomed-in on an object. EI For adjusting backlight compensation. Use this setting to adjust the backlight compensation when an image is backlit. ON OFF 5 Backlight compensation No backlight compensation is applied. Digital video recorder or time-lapse VCR : VIDEO IN : VIDEO OUT 12 Bracket screws (Longer) 3 4 5 Sync setting (LL) 1 Loosen the LOCK screw 2 A Connections q What you will need · Peripheral equipment (such as monitor, digital video recorder or time-lapse VCR) · Cables for connecting peripheral equipment and camera (coaxial cables, connecting plugs) · Power adapter (24 V AC or 12 V DC) · Attachable lens (Auto-iris lens recommended. ) q Making connections 1 Connect the camera and peripheral equipment with cables. 2 Connect the power cable. Secure the supplied clamping core to the power cable as shown in Figure A. <When using a 24 V AC adapter> Connect 3 wire grounded cable# (use 18AWG+) to the ground (GND) terminal as shown in Figure 1. <When using a 12 V DC adapter> Connect the cable as shown in Figure 2. CAUTION · When connecting the power cable to the camera, check that the polarity is correct. · To prevent fire hazard any UL listed wire rated VW-1, should be used for the 24 V AC cable input terminal. Vertical sync disturbance may occur when a selector is used to switch between multiple cameras connected to one monitor. To prevent vertical sync disturbance, set to "ON. " ON OFF 5 Line-Lock · Adjust PHASE dial Internal Sync to eliminate sync disturbance. 3 · Line-Lock: Synchronizes the unit with power frequency. CAUTION If the image disturbance doesn't disappear after adjusting the PHASE dial ( ) on the second and subsequent cameras, adjust the PHASE dial ( ) on the first camera. [. . . ] Subject to the OBLIGATIONS above and EXCLUSIONS below, SANYO Fisher Company warrants this SANYO product against defects in materials and workmanship for the periods specified below. SFC will repair or replace (at its option) the product and any of its parts which fail to conform to this warranty. The warranty period commences on the date the product was first purchased or rented at retail. LABOR 3 YEARS PARTS 3 YEARS IMAGE DEVICE 3 YEARS · Depending on the type of lens, the shape of the lens plug may differ. [. . . ]