User manual SANYO VCB-3374

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual SANYO VCB-3374. We hope that this SANYO VCB-3374 user guide will be useful to you.


SANYO VCB-3374 : Download the complete user guide (273 Ko)

Manual abstract: user guide SANYO VCB-3374

Detailed instructions for use are in the User's Guide.

[. . . ] This warranty does not apply to uncrating, setup, installation, removal of the product for repair or reinstallation of the product after repair. This warranty does not apply to repairs or replacements necessitated by any cause beyond the control of SFC including, but not limited to, any malfunction, defect or failure caused by or resulting from unauthorized service or parts, improper maintenance, operation contrary to furnished instructions, shipping or transit accidents, modification or repair by the user, abuse, misuse, neglect, accident, incorrect power line voltage, fire, flood or other Acts of God, or normal wear and tear. The foregoing is in lieu of all other expressed warranties and SFC does not assume or authorize any party to assume for it any other obligation or liability. THE DURATION OF ANY WARRANTIES WHICH MAY BE IMPLIED BY LAW (INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS) IS LIMITED TO THE TERM OF THIS WARRANTY. [. . . ] Install away from electric or magnetic fields If installed close to a TV, radio transmitter, magnet, electric motor, transformer, audio speakers the magnetic field they generate will distort the image. Protect from humidity and dust To prevent damages to the camera, do not install it where there is greasy smoke or steam, where the dampness may get too high, or where there is a lot of dust. Protect from high temperatures Do not install close to stoves, or other heat generating devices, such as spotlights, etc. , or where it could be subject to direct sunlight, as that could cause deformation, discoloration or other damages. Be careful when installing close to the ceiling, in a kitchen or boiler room, as the temperature may raise to high levels. Install where the temperature range will stay between ­10°C and 50°C. (no condensation) Cleaning · Dirt can be removed from the cabinet by wiping it with a soft cloth. To remove stains, wipe with a soft cloth moistened with a soft detergent solution and wrung dry, then wipe dry with dry soft cloth. · Do not use benzine, thinner or other chemical product on the cabinet, as that may cause deformation and paint peeling. Before using a chemical cloth, make sure to read all accompanying instructions. Make sure that no plastic or rubber material comes in contact with the cabinet for a long period of time, as that may cause damage or paint peeling. English 3 PARTS NAMES 1 Video output connector (VIDEO OUT: BNC type) 1 5 4 Connect this connector to a device such as a VCR or monitor with a VIDEO IN connector. 2 Line phase adjustment screw (LINE PHASE) When using two cameras or more, the image on the monitor may roll vertically when switching sources. This rolling can be minimized by turning this screw. 2 3 3 24 V AC input terminal (24 V AC, GND) 4 External sync composite video signal input connector (VS IN: BNC type) Connect to this connector the synchronizing signal output from a synchronizing signal device or the composite signal of a video distributor. 6 7 1 2 32 5 Power indicator (POWER) Comes on when the power to the camera is on. 6 Lens mount cap The cap is installed to protect the lens mount section. Remove the lens mount cap before installing a lens (sold separately). 1 1 Shorter screws: M3 x 4 2 Longer screws: M3 x 6 3 Camera mounting screw hole: 1/4"-20 UNC 7 Camera installation bracket The bracket can be fixed at the top or bottom of the camera. When fixing the bracket, be sure to use the longer screws and install the shorter screws on the opposite side to seal the openings. CAUTION: When installing the camera support, select a location that can support the total weight of the camera and accessories. 4 English PARTS NAMES 8 Lens iris output connector (4 pin) 8 1 9 2 4 3 This 4-pin connector is used to send the DC control signal and power supply to an auto-iris type lens. 9 Camera setup section (under the cover) This unit factory settings are as indicated below. These settings are for when using a 1/3 inch CS mount DC (without EE internal amplifier) type lens. However, if due to installation conditions or environment the settings may need to be modified for best results (see "SETTINGS"). To access the controls, remove the cover fixing screw, then remove the cover. Control name Position a Electronic iris (EI)/ OFF c VR401 L EI ON OFF ON Backlight compensation (BLC) switch E V E b Auto-iris lens switch (A. I. LENS c Lens iris level volume (LEVEL) ab Note: · The EI/BLC switch is used for an auto-iris lens, therefore the two settings cannot be used simultaneously. · When using a 1/2 or 2/3 inch C mount VIDEO (with EE internal amplifier) auto-iris type lens, set the A. I. Refer to the lens specifications to check the pins connections in the plug. · If they are different than indicated, remove the original plug and connect the supplied plug according to the diagram. [. . . ] A: When using a DC type lens, the LEVEL volume (inside the camera casing) should be adjusted. B: When using a VIDEO type lens, the LEVEL volume (on the lens) should be adjusted. · · · · · · · · · The picture is not clear Is the monitor correctly adjusted?If there is dust or finger prints on the lens, the image quality will deteriorate. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE SANYO VCB-3374




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual SANYO VCB-3374 will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.