User manual SANYO TLS9924P

[. . . ] CAUTION: Changes or modifications not expressly approved by the manufacturer may void the user's authority to operate this equipment. For the customers in Canada This class B digital apparatus complies with Canadian ICES-003. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Location For safe operation and satisfactory performance of your VCR, keep the following in mind when selecting a place for its installation: oe Shield it from direct sunlight and keep it away from sources of intense heat. [. . . ] Alarm recording is done only when there is an alarm trigger during programmed timer recording duration. Alarm recording is not performed even if there is an alarm trigger. 20 English ALARM RECORDING Alarm Recording Counter Display oe During alarm recording, "AL" will be flashing on the digital display. oe If the ON SCREEN switch is set to the "ON" position, the number of alarms will flash on the monitor screen. oe The maximum display number of alarm recordings is "999", at the next alarm recording the counter will indicate "000". oe When the (ALARM TIME) menu is displayed, press the MENU RESET button to reset the alarm counter to "000" (all the data of the (ALARM TIME) menu is reset). Checking the Alarm Recordings Time 1 Press the MENU button until the (ALARM TIME) menu is displayed. ø The number of alarm recordings, and the 8 most recent alarm recording times are displayed. 09-25@10:52 Connections to the ALARM IN/OUT Terminals oe Alarm input signal Connect a make-contact (no voltage) switch between the ALARM IN and COM terminals. oe Alarm output signal Normally DC 5V are output between the ALARM OUT and the COM terminals. When an alarm input (trigger) is received and the unit is recording, the output falls to 0V. Once the alarm recording is over, the output returns to DC 5V. NOTE: oe The data for the previous alarm recordings is erased. 2 Press the SEARCH/AUDIO ON button, the normal screen is displayed. NOTE: oe If the MENU RESET button is pressed while the (ALARM TIME) menu is displayed, the displayed data is erased. "AL" will be erased from the digital display. ALARM RESET IN terminal oe If the circuit between the ALARM RESET IN terminal and COM terminals is closed during alarm recording, alarm recording mode is canceled. English 21 ALARM RECORDING Alarm Search To go to the beginning of a desired alarm recording. Alarm Scan To look for an alarm recording by viewing the first 5 seconds of each alarm recording. 1 Press the SEARCH/AUDIO ON button during stop mode. 3 Turn the SHUTTLE ring to set the desired start day of the week (ex: SAT), then turn the JOG dial clockwise. ø The recording start hour position starts flashing. G Turn the SHUTTLE ring to select the recording speed mode (ex: 48), then turn the JOG dial clockwise. ø "N" will start flashing. H Turn the SHUTTLE ring to select "Y". ---@N 4 Turn the SHUTTLE ring to set the recording start hour (ex: 21), then turn the JOG dial clockwise. ø The recording start minutes position starts flashing. 5 Turn the SHUTTLE ring to set the recording start minutes (ex: 00), then turn the JOG dial clockwise. ø The recording stop hour position starts flashing. I Follow steps F and G under "PROGRAM TIMER RECORDING" on page 23. 6 Turn the SHUTTLE ring to set "öö" for the recording stop hour. ø The rest of the line settings will change to "öö:öö ööö ö", the day of the next line will change to the next day and the start time will change to "öö:öö" automatically. 7 Turn the JOG dial clockwise. ø The day of the week of the 8th line is flashing. 24 English PROGRAM TIMER RECORDING Setting the Holidays By setting the holidays, timer recording will be conducted on those days, as set for Sundays. Changing a Program Timer Recording 1 Press the MENU button until the (TIMER SET) menu is displayed. 1 Press the MENU button until the (HOLIDAY SET) menu is displayed. ----- 2 Turn the JOG dial, until the setting to correct is flashing. 3 Turn the SHUTTLE ring, to correct the setting. 4 Press the SEARCH/AUDIO ON button to save the settings. 5 Press the TIMER button. 2 Turn the SHUTTLE ring to set the month of the holiday, then turn the JOG dial clockwise. To Cancel a Program Timer Recording 1 Press the MENU button until the (TIMER SET) menu is displayed. 3 Turn the SHUTTLE ring to set the day of the holiday. ø Repeat steps 2 to 4 to set up to 20 holidays. 2 Turn the JOG dial, until the "Y" corresponding to the timer recording to cancel is flashing. 5 Press the SEARCH/AUDIO ON button to save the settings. 3 Turn the SHUTTLE ring, to select "N". 4 Press the SEARCH/AUDIO ON button to save the settings. NOTES: oe If setting holidays, be sure that a timer recording is set for Sunday. [. . . ] After the battery has been replaced, press the ALL RESET button, then enter all the time, date, etc. settings as required. 42 English MAINTENANCE Maintaining and Checking The Mechanism To maintain the VCR functions and features working properly, and to avoid damages or dirt on the tape, it is recommended to follow the maintenance points and periodicity indicated below. For detailed information, please contact your dealer. Maintenance Table PARTS Tape Path System ASSY, BRAKE BAND ASSY, LEVER BT (tape guide) FULL ERASE HEAD ASSY, ROLLER CLEANER ASSY, GUIDE ROLLER ASSY, MOUNTING INCLNE S ASSY, MOUNTING INCLNE T ACE HEAD ASSY, LEVER PINCH ROLLER MOUNTING, LIFT PINCH CAM, LIFT PINCH GEAR, CAM PINCH ASSY, EARTH CYL COMPL, CYLINDER ASSY, CYLINDER UPPER Reel Drive System ASSY, REEL SUPPLY ASSY, REEL TAKEUP GEAR, REEL S GEAR, REEL T PULLEY, REEL SPECIAL, WASHER 2. 4 X 6 X 0. 25 COMPL, MOUNTING CLUTCH BELT, REEL MOTOR, CAPSTAN ASSY, GEAR FRICTION Brake ASSY, BRAKE S ASSY, BRAKE T ASSY, BRAKE CAPSTAN ASSY, BRAKE SOFT T Loading Drive ASSY, LOADING MOTOR System DAMPER COMPL, GEAR WORM CAM, MAIN SPECIAL WASHER 3. 6 X 0. 5 GEAR, WHEEL 1 GEAR, WHEEL 2 MODE SWITCH SLIDE, CRECENT GEAR, LOAD S GEAR, RACK FRONT GEAR, RACK START GEAR, PINON Performance BACK TENSION TORQUE Check FWD, REW TORQUE PLAY TORQUE REV TORQUE 2000H E F F E F F F F F 4000H k F F k F F F F k F : Cleaning 6000H E F F E F F F F F E : Confirmation 8000H k F k k F k k k k k k k k F(k) F(k) Fv Fv v v v E k k k vk E E E k k k k k k k k k k k k k k E E E E v : Lubrication NOTES k : Change F F(k) Fv Fv v v v v E F v E E E k F(k) F(k) Fv Fv v v v E k k E(k) vk E E E E E E E E E E E E E E E E E E F F(k) Fv Fv v v v v E(k) v E E E E E E E E E E E PB BACK TENSION TORQUE 25~50gcm FWD, REW TORQUE 600gcm PLAY 55 ~ 110gcm REV 100 ~ 210gcm NOTE: 1. For places with symbols such as E (k) and F (k), carry out checking and cleaning, and replace if necessary. [. . . ]