User manual SANYO TLS1960P

[. . . ] CAUTION: Changes or modifications not expressly approved by the manufacturer may void the user's authority to operate this equipment. For the customers in Canada This class B digital apparatus complies with Canadian ICES-003. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generated, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. [. . . ] 4 Press the SEARCH/AUDIO ON button to save the setting. English 17 NORMAL RECORDING Recording Check The image being recorded can be checked. Setting the Mode at the End of the Tape In the (SET UP 3) menu, you can set the mode of the VCR mode when the tape reaches the end during recording. 1 During recording, press the PLAY (REC CHECK) button. The VCR will then return to the previous recording mode. 1 Press the MENU button until the (SET UP 3) menu is displayed. @Y NOTE: X During recording check operations, recording is suspended momentarily. Clog Detection This VCR is equipped with a clog detection function. When the heads are dirty and the recording quality deteriorates, the output at the WARNING OUT terminal becomes 0V (Low), the "m" indicator flashes on the digital display, and the buzzer sounds. is set to "N", the recording quality is not monitored. 2 Press the * (or +) button, until the "TAPE END MODE" setting is flashing. 3 Press the l (or j) button to set the desired mode. X Setting when the REPEAT REC switch is set to the "OFF" position. The cassette is ejected X Setting when the REPEAT REC switch is set to the "ON" position. Autorepeat recording mode is automatically canceled if there was an alarm trigger R2. Autorepeat recording mode is active even if there was an alarm trigger NOTES: X To cancel the "m" indicator display and reset the WARNING OUT terminal output, press the STOP button. X Clog detection is not possible if recording in 2-hour mode. 4 Press the SEARCH/AUDIO ON button to save the setting. 18 English AUTOREPEAT RECORDING Autorepeat Recording The same tape can be recorded over many times. X Follow the Before starting steps, under "NORMAL RECORDING". NOTES: X If during autorepeat recording there is an alarm trigger, "AL" is displayed on the digital display and alarm recording will take place. (Please refer to page 20, "ALARM RECORDING". ) X If the "TAPE END MODE" setting is R 1, the REPEAT indicator will go off if there is an alarm trigger. Alarm recording is done only if there is an alarm trigger and the VCR is not in programmed timer recording mode. Alarm recording is done only when there is an alarm trigger during programmed timer recording duration. Alarm recording is not performed even if there is an alarm trigger. 20 English ALARM RECORDING Alarm Recording Counter Display X During alarm recording, "AL" will be flashing on the digital display. X If the ON SCREEN switch is set to the "ON" position, the number of alarms will flash on the monitor screen. X The maximum display number of alarm recordings is "999", at the next alarm recording the counter will indicate "000". X When the (ALARM TIME) menu is displayed, press the MENU RESET button to reset the alarm counter to "000" (all the data of the (ALARM TIME) menu is reset). Checking the Alarm Recordings Time 1 Press the MENU button until the (ALARM TIME) menu is displayed. ø The number of alarm recordings, and the 8 most recent alarm recording times are displayed. 09-25@10:52 Connections to the ALARM IN/OUT Terminals X Alarm input signal Connect a make-contact (no voltage) switch between the ALARM IN and COM terminals. X Alarm output signal Normally DC 5V are output between the ALARM OUT and the COM terminals. When an alarm input (trigger) is received and the unit is recording, the output falls to 0V. Once the alarm recording is over, the output returns to DC 5V. NOTE: X The data for the previous alarm recordings is erased. [. . . ] After the battery has been replaced, press the ALL RESET button, then enter all the time, date, etc. settings as required. English 35 MAINTENANCE Maintaining and Checking The Mechanism To maintain the VCR functions and features working properly, and to avoid damages or dirt on the tape, it is recommended to follow the maintenance points and periodicity indicated below. For detailed information, please contact your dealer. Maintenance Table PARTS Tape Path System ASSY, BRAKE BAND ASSY, LEVER BT (tape guide) FULL ERASE HEAD ASSY, ROLLER CLEANER ASSY, GUIDE ROLLER ASSY, MOUNTING INCLNE S ASSY, MOUNTING INCLNE T ACE HEAD ASSY, LEVER PINCH ROLLER MOUNTING, LIFT PINCH CAM, LIFT PINCH GEAR, CAM PINCH ASSY, EARTH CYL COMPL, CYLINDER ASSY, CYLINDER UPPER Reel Drive System ASSY, REEL SUPPLY ASSY, REEL TAKEUP GEAR, REEL S GEAR, REEL T PULLEY, REEL SPECIAL, WASHER 2. 4 X 6 X 0. 25 COMPL, MOUNTING CLUTCH BELT, REEL MOTOR, CAPSTAN ASSY, GEAR FRICTION Brake ASSY, BRAKE S ASSY, BRAKE T ASSY, BRAKE CAPSTAN ASSY, BRAKE SOFT T Loading Drive ASSY, LOADING MOTOR System DAMPER COMPL, GEAR WORM CAM, MAIN SPECIAL WASHER 3. 6 X 0. 5 GEAR, WHEEL 1 GEAR, WHEEL 2 MODE SWITCH SLIDE, CRECENT GEAR, LOAD S GEAR, RACK FRONT GEAR, RACK START GEAR, PINON Performance BACK TENSION TORQUE Check FWD, REW TORQUE PLAY TORQUE REV TORQUE 2000H E F F E F F F F F 4000H k F F k F F F F k F : Cleaning 6000H E F F E F F F F F E : Confirmation 8000H k F k k F k k k k k k k k F(k) F(k) Fv Fv v v v E k k k vk E E E k k k k k k k k k k k k k k E E E E v : Lubrication NOTES k : Change F F(k) Fv Fv v v v v E F v E E E k F(k) F(k) Fv Fv v v v E k k E(k) vk E E E E E E E E E E E E E E E E E E F F(k) Fv Fv v v v v E(k) v E E E E E E E E E E E PB BACK TENSION TORQUE 25~50gcm FWD, REW TORQUE 600gcm PLAY 55 ~ 110gcm REV 100 ~ 210gcm NOTES: 1. For places with symbols such as E (k) and F (k), carry out checking and cleaning, and replace if necessary. [. . . ]