User manual SANYO SBM15

[. . . ] - This fuction does not work for this monitor. 6) +100 -/-Press to select channels over 100. For example, to select channel 121, press "+100", then press "2" and "1". - This fuction does not work for this monitor. 7) VOL Adjusts the audio volume. 8) MUTE Pauses (mutes) the audio output temporarily. The audio resumes if MUTE or - VOL + is pressed in the Mute mode. 9) TTX/MIX TV channels provide text information services via teletext. - This fuction does not work for this monitor. 10) MENU Opens the on-screen menu and exits from the menu screen or closes the screen adjustment menu. 11) ENTER Activates a highlighted menu item. 12) P. MODE When you press this button, current picture mode is displayed on the lower center of the screen. [. . . ] - This fuction does not work for this monitor. 16) SOURCE Changes the video source. 17) INFO The current picture information is displayed in the top left corner of the screen. 18) EXIT Exits from the menu screen. 19) Up-Down Left-Right buttons Moves from one menu item to another horizontally, vertically or adjusts selected menu values. 20) S. MODE When pressing this button, the current mode is displayed at the bottom centre of the screen. Then press the button again to circle through available preconfigured modes. ( Standard Music Movie Speech Custom ) 21) STILL Press the button once to freeze the screen. Press it again to unfreeze. 22) FM RADIO Turns the FM Radio on/off. In areas where the signal is weak, noise may occur during FM radio broadcasts. - This fuction does not work for this monitor. 23) P. SIZE Press to change the screen size. 24) SRS SRS 25) DUAL/MTS DUALSTEREO/MONO, DUAL l / DUAL ll and MONO/NICAM MONO/NICAM STEREO can be operated depending on the broadcasting type by using the DUAL button on the remote control while watching TV. MTSYou can select MTS (Multichannel Television Stereo) mode. Audio Type MTS/S_Mode Mono Mono Mono Stereo Mono SAP Default Manual Change Mono FM Stereo Stereo SAP - This fuction does not work for this monitor. 26) PIP Every time you press the button, a PIP screen appears. 27) SOURCE Changes the source of the PIP window signal. 28) SWAP Swaps the contents of the PIP and main image. The image in the PIP window will appear on the main screen, and the main screen image will appear in the PIP window. 29) SIZE Switches the PIP Picture Size. 30) REW Rewind 31) STOP Stop 32) PLAY / PAUSE Play/Pause 33) FF Fast forward © 1995~2007 SANYO. ALL Rights Reserved Select Language Main Page Model SyncMaster SBM15 Safety Instructions Introduction Connections Installing the Stand KIT Connecting the LCD Display Using the Software Adjusting the LCD Display Troubleshooting Specifications Information Appendix The color and appearance of the product may vary depending on the model, and the product specifications are subject to change without prior notice for reasons of performance enhancement. Connections Installing the Stand KIT Note · Only the supplied bolts should be used. Caution Samsung Electronics will not be responsible for damages caused by using a base other than those specified. Installing the Semi Stand Left stand Right stand Caution Make sure to install the stand with the Caution label folded backwards. 1) A 'Cover-Protector' is used to protect the hole at the bottom of the LCD Display , where the stand is inserted. Be sure to remove the 'Cover-Protector' when attaching the provided Semi Stand or Stand KIT (sold separately) and cover the hole using the 'Cover-Hole' when attaching the wall mount kit. 2) 3) Set up the left and right stands respectively. (M4 x L15) Caution This stand is designed for adjusting the screen angle. The company is not responsible for any problem caused when using this stand. · Do not use benzene, thinner or other flammable substances, or a wet cloth. · We recommend that a Samsung cleansing agent is used to prevent damage to the screen. 2) Maintaining the Flat Panel Display Screen. (They may cause flaws or deformation of the screen surface. ) · The user will be required to pay costs and related expenses for repairing damages caused. Symptoms and Recommended Actions Note · A LCD Display recreates visual signals received from the computer. Therefore, if there is a problem with the computer or the video card, this can cause the LCD Display to become blank, have poor coloring, become noisy, and video mode not supported, etc. In this case, first check the source of the problem, and then contact a Service Center or your dealer. 1) 2) Check if the power cord and the video cables are properly connected to the computer. (If it does, request an a service for the main board of the computer. ) 3) 4) If you installed a new video card or if you assembled the PC, check if you installed the Adaptor(video). Check if the scanning ratio of the video screen is set to between 50 Hz ~ 85 Hz. (Do not exceed 60Hz when using the maximum resolution. ) 5) If you have problems in installing the Adaptor (video) driver, boot the computer in Safe Mode, remove the Display Adaptor in the "Control Panel, System, Device Administrator" and then reboot the computer to reinstall the Adaptor (video) driver. Check List Note · The following table lists possible problems and their solutions. Before calling for assistance, check the information in this section to see if you can remedy any problems for yourself. If you do need assistance, please call the phone number on the Information section or contact your dealer. Problems related to the Installation (PC Mode) Note · Problems related to the LCD Display installation and their solutions are listed. Problems The LCD Display screen flickers. Solutions Check if the signal cable between the computer and the LCD Display is securely connected. (Refer to Connecting a Computer) Problems related to the Screen Note · Problems related to the LCD Display screen and their solutions are listed. Problems The screen is blank and the power indicator is off. Solutions Ensure that the power cord is firmly connected and the LCD LCD Display is on. [. . . ] If not, reset them referring to the current Information under the LCD Display menu and Preset Timing Modes. The image is too light or too dark. Adjusts the brightness and contrast. (Refer to the Brightness, Contrast) The screen color is inconsistent. The color white is poor. Adjust color using Custom under OSD Color Adjustment menu. The power Indicator blinks green. The LCD Display is currently saving the changes made to the settings to the OSD memory. The screen is blank and the power indicator light is steady green or blinks every 0. 5 or 1 seconds. The LCD Display is using its power management system. Press a key on the keyboard. The screen is blank and it is blinking. If you see the "TEST GOOD" message on the screen when you pressing the MENU button, check the cable connection between the LCD Display and the computer to ensure that the connector is properly connected. Problems related to Audio Note · Problems related to audio signals and their solutions are listed below. Problems No sound. Solutions Ensure that the audio cable is firmly connected to both the audio-in port on your LCD Display and the audio-out port on your sound card. [. . . ]