User manual SANYO R227

[. . . ] If the problem still persists, contact the sales dealer where you purchased the projector or the service center. SAFETY PRECAUTIONS WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. Be especially careful that children do not stare directly into the beam. q Take appropriate space on the top, sides and rear of the projector cabinet for allowing air circulation and cooling the projector. If the projector is to be built into a compartment or similarly enclosed, the minimum distances must be maintained. [. . . ] When selecting Computer, this projector automatically tunes to incoming signal and projects proper image without any special setting. (Some computers need setting manually. ) Note : Projector may display one of following messages. Auto When projector cannot recognize connected signal as PC system provided in this projector, Auto PC Adjustment function operates to adjust projector and message "Auto" is displayed on SYSTEM Menu icon. (Refer to P28. ) When image is not provided properly, manual adjustment is required. (Refer to TROUBLESHOOTING on page 47. ) PC SYSTEM MENU PC SYSTEM Menu icon Displays system being selected. ­­­­ D-VGA, D-SVGA, D-XGA, D-SXGA 1, D-SXGA 2, D-SXGA3 or D-UXGA When digital computer signal is received on DVI terminal, above message is displayed on PC SYSTEM Menu icon. SELECT COMPUTER SYSTEM MANUALLY This projector automatically selects PC system among those provided in this projector and PC system can be also selected manually. PC SYSTEM MENU 1 2 Press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT buttons to move a red frame pointer to PC SYSTEM Menu icon. Press POINT DOWN button to move a red arrow pointer to system that you want to set, and then press SELECT button. PC SYSTEM Menu icon Displays system being selected. (P29, 30) 26 COMPUTER INPUT COMPATIBLE COMPUTER SPECIFICATIONS Basically this projector can accept a signal from all computers with V, H-Frequency mentioned below and less than 230 MHz of Dot Clock. ON-SCREEN DISPLAY RESOLUTION H-Freq. (Hz) VGA 1 VGA 2 VGA 3 VGA 4 VGA 5 VGA 6 VGA 7 MAC LC13 MAC 13 RGB RGB 480p 575p SVGA 1 SVGA 2 SVGA 3 SVGA 4 SVGA 5 SVGA 6 SVGA 7 SVGA 8 SVGA 9 SVGA 10 SVGA 11 MAC 16 XGA 1 XGA 2 XGA 3 XGA 4 XGA 5 XGA 6 XGA 7 XGA 8 XGA 9 XGA 10 XGA 11 XGA 12 640 x 480 720 x 400 640 x 400 640 x 480 640 x 480 640 x 480 640 x 480 640 x 480 640 x 480 ­­­­­­­­ (Interlace) ­­­­­­­­ (Interlace) ­­­­­­­­ (Progressive) ­­­­­­­­ (Progressive) 800 x 600 800 x 600 800 x 600 800 x 600 800 x 600 800 x 600 800 x 600 800 x 600 800 x 600 800 x 600 800 x 600 832 x 624 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 (Interlace) 1024 x 768 1024 x 768 1024 x 768 (Interlace) 31. 47 31. 47 31. 47 37. 86 37. 86 37. 50 43. 269 34. 97 35. 00 15. 734 15. 625 31. 47 31. 25 35. 156 37. 88 46. 875 53. 674 48. 08 37. 90 34. 50 38. 00 38. 60 32. 70 38. 00 49. 72 48. 36 68. 677 60. 023 56. 47 60. 31 48. 50 44. 00 63. 48 36. 00 62. 04 61. 00 35. 522 59. 88 70. 09 70. 09 74. 38 72. 81 75. 00 85. 00 66. 60 66. 67 30 25 59. 88 50 56. 25 60. 32 75. 00 85. 06 72. 19 61. 03 55. 38 60. 51 60. 31 51. 09 60. 51 74. 55 60. 00 84. 997 75. 03 70. 07 74. 92 60. 02 54. 58 79. 35 43. 59 77. 07 75. 70 43. 48 XGA 13 XGA 14 XGA15 MAC 19 MAC 21 SXGA 1 SXGA 2 SXGA 3 SXGA 4 SXGA 5 SXGA 6 SXGA 7 SXGA 8 SXGA 9 SXGA 10 SXGA 11 SXGA 12 SXGA 13 SXGA 14 SXGA 15 SXGA 16 SXGA 17 SXGA 18 SXGA 19 SXGA 20 SXGA 21 MAC MAC UXGA 1 UXGA 2 UXGA 3 UXGA 4 720p 1035i 1080i60 1080i50 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1152 x 870 1152 x 864 1280 x 1024 1280 x 1024 1280 x 1024 1280 x 1024 1280 x 1024 1280 x 1024 1280 x 1024 1280 x 1024 1280 x 960 1152 x 900 1152 x 900 1280 x 1024 (Interlace) 1280 x 1024 (Interlace) 1280 x 1024 1280 x 1024 1152 x 900 1280 x 1024 (Interlace) 1280 x 1024 1280 x 1024 1400 x 1050 1280 x 960 1280 x 1024 1600 x 1200 1600 x 1200 1600 x 1200 1600 x 1200 ­­­­­­­­ (Progressive) ­­­­­­­­ (Interlace) ­­­­­­­­ (Interlace) ­­­­­­­­ (Interlace) 46. 90 47. 00 58. 03 60. 24 68. 68 64. 20 62. 50 63. 90 63. 34 63. 74 71. 69 81. 13 63. 98 79. 976 60. 00 61. 20 71. 40 50. 00 50. 00 63. 37 76. 97 61. 85 46. 43 63. 79 91. 146 63. 93 75. 00 80. 00 75. 00 81. 25 87. 50 93. 750 45. 00 33. 75 33. 75 31. 25 58. 20 58. 30 72. 0 75. 08 75. 06 70. 40 58. 60 60. 00 59. 98 60. 01 67. 19 76. 107 60. 02 75. 025 60. 00 65. 20 75. 60 43. 00 47. 00 60. 01 72. 00 66. 00 43. 35 60. 18 85. 024 60. 00 75. 08 75. 08 60. 00 65. 00 70. 00 75. 00 60. 00 30. 00 30. 00 25. 00 When a input signal is digital from DVI terminal, refer to chart below. ON-SCREEN DISPLAY RESOLUTION H-Freq. (Hz) D-VGA D-SVGA D-XGA D-SXGA 1 640 x 480 800 x 600 1024 x 768 1280 x 1024 31. 469 37. 879 48. 363 63. 981 59. 940 60. 317 60. 004 60. 020 D-SXGA 2 D-SXGA 3 D-UXGA 1280 x 1024 1280 x 1024 1600 x 1200 60. 276 31. 65 75. 00 58. 069 29. 8 60. 00 NOTE : Specifications are subject to change without notice. 27 COMPUTER INPUT PC ADJUSTMENT AUTO PC ADJUSTMENT Auto PC Adjustment function is provided to automatically adjust Fine sync, Total dots and Picture Position to conform to your computer. Auto PC Adj. 1 2 Press MENU button and ON-SCREEN MENU will appear. Display area V Adjustment of vertical area displayed with this projector. Press POINT LEFT/RIGHT button(s) to decrease/increase value and then press SELECT button. Full screen Press POINT LEFT/RIGHT button(s) to switch Full screen function to "On" or "Off. " Set "On" to resize image with 4 x 3 aspect ratio to fit a screen. NOTE : Fine sync, Display area, Display area H, Display area V and Full screen cannot be adjusted when "RGB", "480p", "575p", "720p (HDTV)", "1035i (HDTV)", "1080i50(HDTV)" or "1080i60 (HDTV)" is selected on PC SYSTEM Menu (P26). Press SELECT button at Display area icon and Display area dialog box appears. Display area Press POINT LEFT /RIGHT button(s) to adjust value and then press SELECT button. To store adjustment data. This Mode has parameters being stored. 3 Store To store adjustment parameters, move a red frame pointer to Store icon and then press SELECT button. Move a red arrow pointer to any of Mode 1 to 5 that you want to store and then press SELECT button. Mode free To clear adjustment parameters previously set, move a red frame pointer to Mode free icon and then SELECT button. Move a red arrow pointer to Mode that you want to clear and then press SELECT button. Reset Reset all adjust parameters on adjustment dialog box to previous figure. To clear adjustment data. Vacant Mode Shows values of "Total dots, " "Horizontal, " "Vertical, " "Display area H, " and "Display area V. " Store icon Close this dialog box. [. . . ] NOTE : Moving a projector from a cool temperature location to a warm temperature location may result in moisture condensation on Projection Lens. In such an event, leave a projector OFF and wait until condensation disappears. (See "SETTING" section on page 39. ) q Check Ceiling feature. (See "SETTING" section on page 39. ) Picture is Left/Right reversed. [. . . ]