User manual SANYO PLC-XW57

[. . . ] Multimedia Projector MODEL PLC-XW57 Owner's Manual Features and Design This Multimedia Projector is designed with the most advanced technology for portability, durability, and ease of use. This projector utilizes built-in multimedia features, a palette of 16. 77 million colors, and matrix liquid crystal display (LCD) technology. Compact Design This projector is designed compact in size and weight. Compatibility The projector widely accepts various video and computer input signals including: C o m p u t e r s , 6 C o l o r s y s t e m s ( PA L , SECAM, NTSC, NTSC4. 43, PAL-M, and PAL-N), Component video, S-Video and RGB scart. [. . . ] Stored data can be called up by selecting "Image" in the Image Level Selection on page 30. Quit Exit the Image Adjust Menu. Store item Press the SELECT button at this item to store the adjusted data. Move the red framed pointer to any of Image 1 to 4 where you want to set and then press the SELECT button. Screen Size Adjustment This projector has the picture screen resize function, which enables you to customize the image size. 1 2 Press the MENU button to display the On-Screen Menu. Press the Point buttons to move the red framed pointer to the Screen Menu icon. Press the Point buttons and move the red framed pointer to the function that you want to select and then press the SELECT button. Normal Screen Menu Screen Menu icon Move the red framed pointer to the function and press the SELECT button. Provide the image to fit the screen size. When the original image size is larger than the screen size (104 x 768 ), this projector enters panning mode automatically. Wide Provide the image to fit wide video aspect ratio (16:9) by expanding the image width uniformly. This function can be used for providing a squeezed video signal at 16:9. Full Provide the full screen image. Note: · This Screen Menu cannot be operated when 70p(HDTV), 1035i (HDTV), or 1080i (HDTV) is selected in the PC System Menu (p. 6). · The projector cannot display any resolution higher than 1600x100. If your computer's screen resolution is higher than it, reset the resolution to the lower before connecting to the projector. · The image data in other than XGA (104x768) is modified to fit the screen size in initial mode. · True, Full, and Digital zoom +/­ cannot be selected when 480i, 575i, 480p, or 575p is selected in the PC System Menu (p. 6). 3 Computer Input For zooming in and out the images Digital zoom + When the D. ZOOM + () is pressed, the On-Screen Menu disappears and the message "D. The Panning function can work only when the image is larger than the screen size. Remote Control POINT buttons SELECT button D . ZOOM + button D . ZOOM - button Digital zoom ­ When D. ZOOM ­ () is pressed, the On-Screen Menu disappears and the message "D. To exit the Digital zoom +/­ mode, press any button except the D. ZOOM buttons, SELECT, and Point buttons. To return to the previous screen size, select a screen size from the Screen Size Adjustment or select an input source from the Input Source Selection (p. 5) again, or adjust the screen size with the D. ZOOM buttons. Note: · The panning function may not operate properly if the stored Mode in the PC Adjust Menu is used. (p. 9) · The minimum compression ratio can be limited depending on the input signal or when the Keystone function is working. · True, Full, and Digital zoom +/­ cannot be selected when 480i, 575i, 480p, or 575p is selected in the PC System Menu (p. 6). · Digital zoom +/- cannot be selected when Full or True is selected. 33 Video Input Input Source Selection (Video) Direct Operation Choose Video by pressing the INPUT button on the top control or the VIDEO button on the remote control. Top Control INPUT button Video Computer 1 Computer 2 Remote Control VIDEO button Video Menu Operation Input Menu icon 1 2 Press the MENU button to display the On-Screen Menu. Press the Point buttons to move the red framed pointer to the Input Menu icon. [. . . ] Total dots Horizontal Vertical Current mode Clamp Display area - H Display area - V Reset Mode free Yes/No Mode 1 Mode Mode 3 Mode 4 Mode 5 Quit Store Mode 1 Mode Mode 3 Mode 4 Mode 5 Quit Quit Quit H-sync freq. Quit Red Green Blue Sharpness Gamma Reset Store 0 - 31 Image Adjust Contrast Brightness Color temp. 0 - 63 0 - 63 High Mid Low XLow Adj. 0 - 63 0 - 63 0 - 63 0 - 15 0 - 15 Yes/No Image 1 Image Image 3 Image 4 Quit Screen Normal True Wide Full Digital zoom + Digital zoom ­ 59 Appendix Video Input System (2) Auto PAL SECAM NTSC NTSC 4. 43 PAL-M PAL-N Setting Setting Language English German French Italian Spanish Portuguese Dutch Swedish Finnish Polish Hungarian Romanian Russian Chinese Korean Japanese Quit System (3) Auto 1080i 1035i 70p 575p 480p 575i 480i Keystone Blue back Display Logo Store/Reset On/Off On/Countdown off/Off Logo select Off Default User Capture Yes/No Logo PIN code lock Logo PIN code Off On Logo PIN code change Quit Quit Image Select Dynamic Standard Cinema Blackboard (Green) Image 1 Image Image 3 Image 4 Image Adjust Contrast Brightness Color Tint Color temp. 0 - 63 0 - 63 0 - 63 0 - 63 High Mid Low XLow Adj. Ceiling Rear Terminal Input search Power management On/Off On/Off Computer /Monitor out On1/On/Off Off Ready Shut down Timer (1-30 Min. ) Quit On/Off Normal/Auto/Eco Code 1/Code Key lock Off Projector Remote Control Quit PIN code lock PIN code lock Off On1 On PIN code change Quit Quit Red Green Blue Sharpness Gamma Noise reduction 0 - 63 0 - 63 0 - 63 0 - 15 0 - 15 Off L1 L On start Lamp control Remote control Security Progressive Off L1 L Film Reset Store Yes/No Image 1 Image Image 3 Image 4 Quit Fan Fan control Lamp counter L1/L Quit Screen Normal Wide Factory default Quit Off/ On1/ On Hour(s) Reset Quit Yes/No 60 Appendix Indicators and Projector Condition Check the indicators for projector condition. Indicators LAMP POWER WARNING REPLACE red red/green yellow Projector Condition The projector is off. [. . . ]