User manual SANYO XP57 PJ-NET ORGANIZER

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual SANYO XP57. We hope that this SANYO XP57 user guide will be useful to you.


SANYO XP57 PJ-NET ORGANIZER: Download the complete user guide (9489 Ko)

Manual abstract: user guide SANYO XP57PJ-NET ORGANIZER

Detailed instructions for use are in the User's Guide.

[. . . ] index POA-PN03C D DC C O 8V U T 10 0m A VID EO IN LIN K ACT PJ-Net Organizer plus IIC NetworkCapture3 NetworkViewer3 NetworkCommunication OWNER'S MANUAL XP57 Series Compliance Federal Communication Commission Notice This equipment has been tested and found to comply SANYO POA-PN03C with the limits for a Class B digital device, pursuant to Tested To Comply part 15 of the FCC Rules. These limits are designed to With FCC Standards provide reasonable protection against harmful interference in a residential installation. This equipment generFOR HOME OR OFFICE USE ates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. [. . . ] Deleting from the multi-control * The multi control item is not changed during using the network viewer function. It is not available with the light mode. Status If some of the registered projectors are disabled by some reasons (such as disconnecting the power source, disconnecting the LAN cable, disconnecting from the network), control changes will continue to be effective for the projectors that are still active. At the same time, the deactivated projectors are excluded from the multicontrol. The status of the registered projectors are indicated under the projector name. See the table below for status indications. Status Status Description (blank) . . . . . . . . . . . . . . . . . . . . . The projector is connected to the network correctly Noconnect . . . . . . . . . . Please check the connection and network configuration of this projector. Check if this projector is using the Network Capture function or Network Viewer function individually, or in the standby mode. * The network unit updates the status at the time when the multi-control function was executed. If the multi-controlled projector is in the standby mode, any change is not effective except timer setting. Cannot register, delete or change the multi-control setting during using the network viewer function. It is recommended that a specified projector should be chosen for setting as a master when you use this multi-control function. The control for the multi-controlled projectors will become too complicated operation if this function is used for each projector. If the registered projector is not connected to the network, it will take some time to complete the multi-control operation because of waiting for the response from each registered projector. There are some disabled items in the multi-control function for the light mode. PJ-NET ORGANIZER OWNER'S MANUAL [XP57 Series] ENGLISH Chapter 4 Controlling the Projector Conf. & Change page in the light mode Following functions in the "Conf. & Change" page are not available in the light mode. - Changing the control mode. - Deleting the registered IP address - Indicating the each status - Indicating the each memo This indicates that the mode is "VisualControl". This indicates that the mode is "Control". Connectionstatus Blinking: Connected Gray: Disconnected (Conf. &Change page in the light mode) Controlling all together "Power & Status", "PC adjustment", "Control" and "Setting" can be controlled all together. Set "ON" the multi control setting and adjust controls of each menu. The setting value is applied to the registered projectors sequentially . This is effective only if the multi control item of the registered projector sets to either "Control&Image" or "Control". Setting all together "E-mail setting", "SNMP setting" and "Timer" can be set all together. The setting value is applied to the registered projectors sequentially. This is effective only if the multi control item of the registered projector sets to either "Control&Image" or "Control". Multi-control Viewer auto setting all together "Viewer auto display" can be set all together. Set "ON" the multi control setting and select [3] Auto display setting from Viewer sub menu (selected by "Multi-control" "Network Viewer" menu). Set the display time periods and repeat times for the auto image display. [. . . ] For further information please contact your network administrator (+ p. 38). It may be required for the authentication depending on the SMTP server. This product does not support this kind of SMTP server. PJ-NET ORGANIZER OWNER'S MANUAL [XP57 Series] 11 ENGLISH Chapter 7 Appendix Q A Can I update the firmware of the network unit. It is possible to update the firmware through the network. The version number of the firmware is indicated on the lower part of the "Initial setting" page. Version of the firmware 10 Q&A Q A What are the rules for IP address assignment? If the network is constructed with TCP/IP protocol, a unique IP address is required for each piece of network equipment. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE SANYO XP57




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual SANYO XP57 will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.