User manual SANYO POA-PN03

[. . . ] index POA-PN03 LIN K ACT PJ-Net Organizer lus II Network Capture 3 Network Viewer 3 Network Communication OWNER'S MANUAL Compliance Federal Communication Commission Notice This equipment has been tested and found to comply SANYO POA-PN03 with the limits for a Class B digital device, pursuant to Tested To Comply part 15 of the FCC Rules. These limits are designed to With FCC Standards provide reasonable protection against harmful interference in a residential installation. This equipment generFOR HOME OR OFFICE USE ates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. [. . . ] The setting value is applied to the registered projectors sequentially . This is effective only if the multi control item of the registered projector sets to either "Both control" or "Control". Setting all together "E-mail setting", "SNMP setting" and "Timer" can be set all together. The setting value is applied to the registered projectors sequentially. This is effective only if the multi control item of the registered projector sets to either "Both control" or "Control". 66 Multi-control Viewer auto setting all together "Viewer auto display" can be set all together. Set "ON" the multi control setting and select [3] Auto display from Viewer sub menu. Set the display time periods and repeat times for the auto image display. When clicking Start button, the registered projectors start playing back the auto image display in sequential. For further information of the Auto display, see "Using the net- work viewer function". (p. 98) This is effective only if the multi control item of the registered projector sets to either "Both control" or "Visual control". PJ-NET ORGANIZER OWNER'S MANUAL 67 ENGLISH Chapter 4 Controlling the Projector 68 Chapter 5 Network Capture Network Capture is a function to display the screen image of the computer via the network. - Real Time Capture - Network Communication 5 PJ-NET ORGANIZER OWNER'S MANUAL 69 ENGLISH Chapter 5 Network Capture About Network Capture function The Network Capture is a function to project the screen images of the computer which has a Network Capture 3 software by the projector through the network. This function has 2 kinds of mode as the below. - Real Time Capture (p. 72) A function to display the screen image of the computer by the projector through the network in real time. - Network Communication (p. 77) This mode is to communicate by sharing the capture image of a computer with multiple computers and a projector. User can draw the text and figure on the captured image by using a drawing tool. Up to 30 computers can be registered. The Network Capture function cannot be used when using the Network Viewer function. The Real Time Capture and Network Communication mode cannot be used at the same time. Launching the Network Capture 3 After installing the Network Capture 3 software, the shortcut icon is copied into the "Startup" folder. When you boot the computer, the Network Capture software also starts and its icon stays on the task bar. If the icon is not appeared on the task bar, the Network Capture 3 software is not starting. Click "Network Capture 3" from "Start" - "All the Programs" - "Network Viewer & Capture 3" menu to launch it manually. The status which the Network Capture 3 icon stays on the task bar is just preparing the screen capturing. Commands on the task bar When clicking the Network Viewer & Capture 3 icon on the task bar, The popup menu will appear as the right. See the next page for each operation. 70 About Network Capture function Items Description Start real time capture . . . . . . . . . . . . . . . . . . Starts the real time capturing. (p. 72) The screen image of the computer is projected on the screen in real time. Start communication . . . . . . . . . . . . . . . . . . . . Starts the Network Communication. Parameter set up. . . . . . . . . . . . . . . . . . . . . . . . . . . . Sets the communication parameter between the computer and network unit of the projector. (p. 71) Version information. . . . . . . . . . . . . . . . . . . . . . . Displays the version of this software. Shut down . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Quits the application. Parameter set up 1 Click Network Capture 3 icon on the task bar. The set3 Set Capture Port and PIN code to match to the projector's port number and Network PIN code. see item "Control by the web browser" ( p. 74). [. . . ] The version number of the firmware is indicated on the lower part of the "Initial Setting" page. Version of the firmware 128 Q&A Q What are the rules for IP address assignment?A If the network is constructed with TCP/IP protocol, a unique IP address is required for each piece of network equipment. Rule1 Do not configure the same IP address to the network equipment in the same network group. If the IP address is set [192. 168. x. x], the Subnet Mask should be set [255. 255. 255. 0] for example. [. . . ]