User manual SANYO PLV75L

[. . . ] Multimedia Projector MODEL PLV-75/PLV-80 PLV75L/PLV-80L (Lensless) Owner's Manual TO THE OWNER Before operating this projector, read this manual thoroughly and operate the projector properly. Operating the projector properly enables you to manage those features and maintain it in better condition for a considerable time. Improper operation may result in not only shortening the product life, but also malfunctions, fire hazard, or other accidents. If your projector seems to operate improperly, read this manual again, check operations and cable connections and try the solutions in the "Troubleshooting" section in the end of this booklet. [. . . ] Quit Closes PC ADJUST MENU. Mode 1 Mode 2 Mode 3 Mode 4 Mode 5 Stored Free Free Free Free To store adjustment data. This Mode has parameters being stored. Vacant Mode Close this dialog box. Shows values of "Total dots, " "Position H, " "Position V, " "Display area H, " and "Display area V. " To clear adjustment data. Mode 1 Mode 2 Mode 3 Mode 4 Mode 5 Stored Free Free Free Free Close this dialog box. 28 COMPUTER INPUT PICTURE IMAGE SELECT IMAGE LEVEL SELECT (DIRECT) Select image level among Standard, Real, Image 1 to Image 10 by pressing IMAGE button on Top Control or IMAGE SELECTION / button on Remote Control Unit. Image 10 IMAGE 1~10 User preset picture adjustment in IMAGE ADJUST Menu (P37). IMAGE button Standard Real Image 1 IMAGE LEVEL SELECT (MENU) 1 2 Press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT buttons to move a red frame pointer to IMAGE SELECT Menu icon. Press POINT UP/DOWN buttons to move a red frame pointer to level that you want to set and then press SELECT button. Standard IMAGE SELECT MENU Image 1 SVGA 1 IMAGE SELECT Menu icon Normal picture level preset on this projector. IMAGE 1~10 User preset picture adjustment in IMAGE ADJUST Menu (P37). Move a red frame pointer to level and press SELECT button. 29 COMPUTER INPUT PICTURE SCREEN ADJUSTMENT This projector has a picture screen resize function, which enables you to display desirable image size. PICTURE SCREEN SELECT (DIRECT) Select picture screen among Normal, Full and True by pressing SCREEN button on Remote Control Unit. SCREEN button Normal Full True PICTURE SCREEN SELECT (MENU) 1 2 Press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT buttons to move a red frame pointer to SCREEN Menu icon. Press POINT UP/DOWN buttons and move a red frame pointer to function that you want to select and then press SELECT button. SCREEN MENU SCREEN Menu icon Move a red frame pointer to function and press SELECT button. Normal Provides image to fit the panel size of the screen. NOTE Full Provides image to fit the horizontal size of the screen. When the original image size is larger than screen size (1366 X 768), this projector enters "D. Digital zoom + When Digital zoom + is selected, ON-SCREEN MENU disappears and message "D. A projected image can be also expanded by pressing D. ZOOM and SELECT button on Remote Control Unit. Digital zoom ­ When Digital zoom ­ is selected, ON-SCREEN MENU disappears and message "D. A projected image can be also compressed by pressing D. ZOOM and SELECT button on Remote Control Unit. To cancel Digital Zoom +/­ mode, press any button except D. ZOOM, SELECT and POINT buttons. Picture screen adjustment can not be operated when "720p (HDTV)", "1035i (HDTV)" or "1080i (HDTV)" is selected on PC SYSTEM Menu (P25). True and Digital zoom +/- can not be selected when "480i", "575i", "480p" or "575p" is selected on PC SYSTEM Menu (P25). This projector cannot display any resolution higher than 1600 X 1200. If your computer's screen resolution is higher than 1600 X 1200, reset resolution to lower before connecting projector. Image data in other than XGA (1024 x 768) is modified to fit screen size in initial mode. Panning function may not operate properly if computer system prepared on PC ADJUST Menu is used. 30 VIDEO INPUT SELECTING INPUT SOURCE DIRECT OPERATION Select INPUT source by pressing INPUT button on Top Control or on Remote Control Unit. [. . . ] (The projector is preparing for standby or the projection lamp is being cooled down. The projector cannot be turned on until cooling is completed. ) The lamp cannot light up. (The lamp has been cooled down enough and the projector is in stand-by mode and ready to be turned on with the POWER ON-OFF button. ) The life of the projection lamp draws to an end. The indicator will turn off. · · · on When · · · flashing · · · dim · · · off the life of the projection lamp draws to an end, the LAMP REPLACE indicator lights yellow. [. . . ]