User manual SANYO PLV55WM1

[. . . ] LCD Projection Monitor MODEL PLV-55WM1 Owner's Manual Table of Contents Table of Contents . . 7 Installing the LCD Projection Monitor Front Back Front Jacks Rear Terminals Remote Control Remote Control Operating Range Remote Control Batteries Installation Remote Control Code Connecting the AC Power Cord Connecting to a Computer and Video Equipment (Video, S-Video) Connecting to Video Equipment (Component, DVI compatible with HDCP) Turning On the LCD Projection Monitor Turning Off the LCD Projection Monitor Sound Adjustment Audio Selection Lamp Control Function Picture Freeze Function On-Screen Menu Menus Audio Adjustment Input Source Selection (INPUT 3 / RGB, Video (Video conference), Component) Input Source Selection (INPUT 4 / Video (Video conference), S-video, Component) Input Source Selection (INPUT 5 / Video (Video conference) ) Video System Selection Image Level Selection Image Level Adjustment Screen Size Adjustment 7 8 9 10 11 12 13 13 14 15 16 17 18 18 19 19 20 20 21 22 24 Computer Input . . 33 Input Source Selection (INPUT 1 / PC digital, AV HDCP) 33 Input Source Selection (INPUT 2 / PC analog) 34 Computer System Selection 35 Computer Adjustment (Auto) 36 Computer Adjustment (Manual) 37 Image Level Selection 39 Image Level Adjustment 40 Screen Size Adjustment 41 Part Names and Functions . . 42 Setting Warning Indicator Cleaning the Air Filter Cleaning the LCD Projection Monitor Lamp Replacement Lamp Replace Counter 42 45 46 46 47 48 Maintenance and Cleaning . [. . . ] Select this item and press the Point Down button to go to the next item. The Image level being selected (p29) Tint cannot be selected when the video system is PAL or SECAM except for 575i. NOTE: 30 Video Input Sharpness Press the Point Left button to soften the image and the Point Right button to sharpen the image. (From -7 to +7) Gamma Press the Point Left / Right button to obtain better balance of contrast. (From -7 to +7) Auto grayscale Press the Point Left / Right button to switch On / Off. When this function is "On", it automatically enhances contrast of bright and dark part of image. Reset To reset the adjusted data, select Reset and press the Point Right button. Store To store the adjusted data, select Store and press the Point Right button. Stored data can be called up by selecting "Image" in the Image Level Selection on page 29. NOTE: The adjusted parameters will be stored in "Image" on the Image Level Selection. Select this item and press the Point Up button to go to the previous item. Press the Point Right button at this icon to store the value. A confirmation box will appear and select [Yes]. Video Input 31 Video Input Screen Size Adjustment Direct Operation You can resize a projected screen with the SCREEN button on the remote control. Remote Control LL AUTO PC LAMP CONTROL LAMP MENU SCREEN SCREEN button Menu Operation This LCD Projection Monitor has a useful function to resize a projected screen. FREEZE SELECT 1 2 Select the Screen Menu with the Point Up / Down button then press the Point Right button to enter the sub-menu. Select an item with the Point Up / Down button and press the SELECT button to set the screen size. Screen Menu + Full Provide an image to fit the width of the screen by expanding the width of the image uniformly. This function can be used to project a squeezed video signal at a wide video aspect ratio of 16 : 9. When your video equipment (such as DVD) has 16 : 9 output mode, select 16 : 9 and select Full in this Screen Menu to provide better quality. Zoom Provide an image to fit the screen size (16 : 9 aspect ratio) by expanding the width and height of the image uniformly. This function can be used to project a letter box mode picture (4 : 3 aspect picture with black bar on the top and bottom edges) at a wide video aspect ratio of 16 : 9. Caption in Provide an image including a caption to fit the screen size (16 : 9 aspect ratio) by expanding the width and height of the image uniformly. Natural wide Modify an image of 4 : 3 aspect ratio to fit the screen size (16 : 9 aspect ratio). It expands the width and height of the image and makes it look natural. NOTE: Screen Menu cannot be selected when 720p or 1080i is selected in the Video System Selection (p28). Full Zoom Caption in Racing is stimulating! Racing is stimulating! Normal Natural wide 32 Computer Input Input Source Selection (INPUT 1 / PC digital, AV HDCP) Direct Operation Select INPUT 1 by pressing the INPUT 1 button on the remote control or pressing the INPUT button on the front panel arbitrary number of times. Before using these buttons, correct input source should be selected through menu operation as described below. See p16-17 for the connection diagrams. INPUT button Front Panel INPUT button INPUT 1 ­AUDIO­R INPUT VO INPUT 2 MENU SELECT 7 INPUT 3 INPUT 4 INPUT 5 FREEZE Remote Control VOLUME INPUT 1 + MUTE INPUT 2 INPUT 1 button AUDIO-S SURROUND INPUT 3 INPUT 4 INPUT 5 Input Menu Menu Operation 1 2 3 Select the Input Menu with the Point Up / Down button, and then press the Point Right button to enter the sub-menu. Select INPUT 1 with the Point Up / Down button and then press the SELECT button or the Point Right button. Move the pointer to the source that you want to select and then press the SELECT button. Computer Input NOTE: HDCP (High-bandwidth Digital Content Protection) is a system for protecting digital entertainment content delivered by DVI (Digital Visual Interface) from being copied. The specification of HDCP is decided and controlled by Digital Content Protection, LLC. Should the specification be changed, this LCD Projection Monitor may not display the digital content protected by HDCP. Source Selection Menu pointer Close the Source Selection Menu. 33 Computer Input Input Source Selection (INPUT 2 / PC analog) Direct Operation Select INPUT 2 by pressing the INPUT 2 button on the remote control or pressing the INPUT button on the front panel arbitrary number of times. [. . . ] Unplug the AC power cord and plug it again to turn on the LCD Projection Monitor. If the LCD Projection Monitor is turned off again, disconnect the AC power cord and contact the dealer or the service center for service and checkup. It may cause an electric shock or a fire hazard. Appendix · · · emits green. · · · blinks green. · · · emits red. [. . . ]