User manual SANYO PLV-70

[. . . ] Multimedia Projector MODEL PLV-70 Owner's Manual TO THE OWNER Before operating this projector, read this manual thoroughly and operate the projector properly. Operating the projector properly enables you to manage those features and maintains it in better condition for a considerable time. Improper operation may result in not only shortening the product-life, but also malfunctions, fire hazard, or other accidents. If your projector seems to operate improperly, read this manual again, check operations and cable connections and try the solutions in the "Trouble-shooting" section of the end of this booklet. [. . . ] Press POINT LEFT/RIGHT button(s) to decrease/increase value and then press SELECT button. Display area V Adjustment of vertical area displayed with this projector. Press POINT LEFT/RIGHT button(s) to decrease/increase value and then press SELECT button. Full screen Press POINT LEFT/RIGHT button(s) to switch Full screen function to "On" or "Off. " Set "On" to resize image to fit the horizontal size of the screen. NOTE : Display area (H/V) and Full screen cannot be adjusted when "1035i (HDTV)" or "1080i (HDTV)" is selected on PC SYSTEM Menu (P23). Press SELECT button at Display area icon and Display area dialog box appears. Display area Press POINT LEFT /RIGHT button(s) to adjust value and then press SELECT button. To store adjustment data. This Mode has parameters being stored. 3 Store To store adjustment parameters, move a red frame pointer to Store icon and then press SELECT button. Move a red arrow pointer to any of Mode 1 to 5 that you want to store and then press SELECT button. Mode free To clear adjustment parameters previously set, move a red frame pointer to Mode free icon and then SELECT button. Move a red arrow pointer to Mode that you want to clear and then press SELECT button. Reset Reset all adjust parameters on adjustment dialog box to previous figure. To clear adjustment data. Vacant Mode Shows values of "Total dots, " "Horizontal, " "Vertical, " "Display area H, " and "Display area V. " Store icon Close this dialog box. Mode free icon 25 COMPUTER INPUT COMPATIBLE COMPUTER SPECIFICATIONS Basically this projector can accept a signal from all computers with V, H-Frequency mentioned below and less than 140 MHz of Dot Clock. ON-SCREEN DISPLAY RESOLUTION H-Freq. (Hz) VGA 1 VGA 2 VGA 3 VGA 4 VGA 5 VGA 6 VGA 7 MAC LC13 MAC 13 RGB RGB SVGA 1 SVGA 2 SVGA 3 SVGA 4 SVGA 5 SVGA 6 SVGA 7 SVGA 8 SVGA 9 SVGA 10 SVGA 11 MAC 16 XGA 1 XGA 2 XGA 3 XGA 4 XGA 5 XGA 6 XGA 7 XGA 8 XGA 9 640 x 480 720 x 400 640 x 400 640 x 480 640 x 480 640 x 480 640 x 480 640 x 480 640 x 480 ­­­­­­­­ (Interlace) ­­­­­­­­ (Interlace) 800 x 600 800 x 600 800 x 600 800 x 600 800 x 600 800 x 600 800 x 600 800 x 600 800 x 600 800 x 600 800 x 600 832 x 624 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 (Interlace) 31. 47 31. 47 31. 47 37. 86 37. 86 37. 50 43. 269 34. 97 35. 00 15. 734 15. 625 35. 156 37. 88 46. 875 53. 674 48. 08 37. 90 34. 50 38. 00 38. 60 32. 70 38. 00 49. 72 48. 36 68. 677 60. 023 56. 47 60. 31 48. 50 44. 00 63. 48 36. 00 59. 88 70. 09 70. 09 74. 38 72. 81 75. 00 85. 00 66. 60 66. 67 30 25 56. 25 60. 32 75. 00 85. 06 72. 19 61. 03 55. 38 60. 51 60. 31 51. 09 60. 51 74. 55 60. 00 84. 997 75. 03 70. 07 74. 92 60. 02 54. 58 79. 35 43. 59 XGA 10 XGA 11 XGA 12 XGA 13 XGA 14 XGA15 MAC 19 MAC 21 SXGA 1 SXGA 2 SXGA 3 SXGA 4 SXGA 5 SXGA 6 SXGA 7 SXGA 8 SXGA 9 SXGA 10 SXGA 11 SXGA 12 SXGA 13 SXGA 14 SXGA 15 SXGA 16 SXGA 17 SXGA 18 SXGA 19 MAC MAC 720p (HDTV) 1035i (HDTV) 1080i (HDTV) 1024 x 768 1024 x 768 1024 x 768 (Interlace) 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1152 x 870 1152 x 864 1280 x 1024 1280 x 1024 1280 x 1024 1280 x 1024 1280 x 1024 1280 x 1024 1280 x 1024 1280 x 1024 1280 x 960 1152 x 900 1152 x 900 1280 x 1024 (Interlace) 1280 x 1024 (Interlace) 1280 x 1024 1280 x 1024 1152 x 900 1280 x 1024 (Interlace) 1280 x 1024 1280 x 960 1280 x 1024 ­­­­­­­­ (Progressive) ­­­­­­­­ (Interlace) ­­­­­­­­ (Interlace) 62. 04 61. 00 35. 522 46. 90 47. 00 58. 03 60. 24 68. 68 64. 20 62. 50 63. 90 63. 34 63. 74 71. 69 81. 13 63. 98 79. 976 60. 00 61. 20 71. 40 50. 00 50. 00 63. 37 76. 97 61. 85 46. 43 63. 79 75. 00 80. 00 45. 00 33. 75 33. 75 77. 07 75. 70 43. 48 58. 20 58. 30 72. 0 75. 08 75. 06 70. 40 58. 60 60. 00 59. 98 60. 01 67. 19 76. 107 60. 02 75. 025 60. 00 65. 20 75. 60 43. 00 47. 00 60. 01 72. 00 66. 00 43. 35 60. 18 75. 08 75. 08 60. 00 30. 00 30. 00 When a input signal is digital from DVI terminal, refer to chart below. ON-SCREEN DISPLAY RESOLUTION H-Freq. (Hz) D-VGA D-SVGA 640 x 480 800 x 600 31. 469 37. 879 59. 940 60. 317 D-XGA 1024 x 768 48. 363 60. 004 NOTE : Specifications are subject to change without notice. 26 COMPUTER INPUT PICTURE IMAGE ADJUSTMENTS IMAGE LEVEL SELECT (DIRECT) Select image level among Standard, Real, Image 1, Image 2, Image 3 and Image 4 by pressing IMAGE button on Top Control or on Remote Control Unit. Select Image 1-4 by pressing IMAGE 1-4 buttons on Remote Control Unit. IMAGE 1~4 User preset picture adjustment in IMAGE ADJUST Menu (P28-29). IMAGE button Standard Real Image 1 Image 2 Image 3 Image 4 IMAGE LEVEL SELECT (MENU) 1 2 Press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT button to move a red frame pointer to IMAGE SELECT Menu icon. Press POINT DOWN button to move a red frame pointer to level that you want to set and then press SELECT button. Standard IMAGE SELECT MENU IMAGE SELECT Menu icon Normal picture level preset on this projector. IMAGE 1~4 User preset picture adjustment in IMAGE ADJUST Menu (P28-29). Level being selected. [. . . ] (See "SETTING" section on page 37. ) q Check Ceiling feature. (See "SETTING" section on page 37. ) Picture is Left/Right reversed. No image. q Check Display feature. (See "SETTING" section on page 37. ) q Check connection between your computer or video equipment and a projector. q When turning a projector on, it takes about 30 seconds to display an image. [. . . ]