User manual SANYO PLCXU40

[. . . ] Multimedia Projector MODEL PLC-XU40 Owner's Manual TO THE OWNER Before operating this projector, read this manual thoroughly and operate the projector properly. Operating the projector properly enables you to manage those features and maintains it in better condition for a considerable time. Improper operation may result in not only shortening the product-life, but also malfunctions, fire hazard, or other accidents. If your projector seems to operate improperly, read this manual again, check operations and cable connections and try the solutions in the "TROUBLESHOOTING" section at the end of this booklet. [. . . ] (Hz) 59. 94 60. 32 60. 00 XGA 12 XGA 13 XGA 14 XGA 15 MAC 19 MAC 21 SXGA 1 SXGA 2 SXGA 3 SXGA 4 SXGA 5 SXGA 6 SXGA 7 SXGA 8 SXGA 9 SXGA 10 SXGA 11 SXGA 12 SXGA 13 SXGA 14 SXGA 15 SXGA 16 SXGA 17 SXGA 18 SXGA 19 SXGA 21 MAC MAC 480p (HDTV) 575p (HDTV) 720p (HDTV) 1035i (HDTV) 1080i 60(HDTV) 1080i 50(HDTV) ON-SCREEN DISPLAY H-Freq. (kHz) 35. 522 46. 90 47. 00 58. 03 60. 24 68. 68 64. 20 62. 50 63. 90 63. 34 63. 74 71. 69 81. 13 63. 98 79. 976 60. 00 61. 20 71. 40 50. 00 50. 00 63. 37 76. 97 61. 85 46. 43 63. 79 63. 90 75. 00 80. 00 31. 47 31. 25 45. 00 33. 75 33. 75 28. 125 H-Freq. (Hz) 86. 96 (Interlace) 58. 20 58. 30 72. 00 75. 08 75. 06 70. 40 58. 60 60. 00 59. 98 60. 01 67. 19 76. 107 60. 02 75. 025 60. 00 65. 20 75. 60 86. 00 (Interlace) 94. 00 (Interlace) 60. 01 72. 00 66. 00 86. 70 (Interlace) 60. 18 60. 00 75. 08 75. 08 59. 88 50. 00 60. 00 60. 00 (Interlace) 60. 00 (Interlace) 50. 00 (Interlace) When an input signal is digital from DVI terminal, refer to the chart below. RESOLUTION 640 x 480 800 x 600 1024 x 768 RESOLUTION 1280 x 1024 1280 x 1024 1280 x 1024 D-VGA D-SVGA D-XGA D-SXGA 1 D-SXGA 2 D-SXGA 3 V-Freq. (Hz) 60. 02 58. 069 29. 80 NOTE : The projector may not project a proper image for D-SXGA 1, D-SXGA 2, and D-SXGA 3 depending on some computers. Specifications are subject to change without notice. 24 COMPUTER INPUT PC ADJUSTMENT AUTO PC ADJUSTMENT Auto PC Adjustment function is provided to automatically adjust Fine sync, Total dots, Horizontal, and Vertical to conform to your computer. Auto PC Adj. 1 2 Press the MENU button and the ON-SCREEN MENU will appear. Press the POINT LEFT/RIGHT button to move the red frame pointer to the PC ADJUST Menu icon. Press the POINT DOWN button to move the red frame pointer to the AUTO PC Adj. This Auto PC Adjustment can also be executed by pressing the AUTO PC ADJ. button on the Remote Control. PC ADJUST MENU PC ADJUST Menu icon Move the red frame pointer to the AUTO PC Adj. Adjustment parameters from Auto PC Adjustment can be memorized in this projector. Once parameters are memorized, the setting can be done just by selecting Mode in the PC SYSTEM Menu (P23). Refer to the step 3 of the MANUAL PC ADJUSTMENT section (P27). NOTE G The PC ADJUST Menu cannot be operated when the input signal is digital or RGB is selected in the PC SYSTEM Menu. G The Fine sync, Total dots, Horizontal, and Vertical of some computers cannot be fully adjusted with this Auto PC Adjustment function. When the image is not provided properly through this function, manual adjustments are required. (Refer to page 26, 27. ) G The Auto PC Adjustment function cannot be operated when "720p (HDTV), " "1035i (HDTV)", or "1080i (HDTV)" is selected in the PC SYSTEM Menu (P23). 25 COMPUTER INPUT MANUAL PC ADJUSTMENT This projector can automatically tune to the display signals from most personal computers currently distributed. However, some computers employ special signal formats which are different from the standard ones and may not be tuned by MultiScan system of this projector. If this happens, the projector cannot reproduce a proper image and the image may be recognized as a flickering picture, a non-synchronized picture, a non-centered picture or a skewed picture. This projector has Manual PC Adjustment to enable you to precisely adjust several parameters to match with those special signal formats. This projector has 5 independent memory areas to memorize those parameters manually adjusted. This enables you to recall the setting for a specific computer whenever you use it. 1 2 Press the MENU button and the ON-SCREEN MENU will appear. Press the POINT LEFT/RIGHT button to move the red frame pointer to the PC ADJUST Menu icon. [. . . ] Check ALL-OFF switch on the Remote Control is set to "ON. " Make sure there is no obstructions between the projector and the Remote Control. Make sure you are not too far from the projector when using the Remote Control. G Make sure the code of the Remote Control is set to conform to the projector. (See the "SETTING" section on page 37. ) G Check cable connection between the projector and your computer. [. . . ]